rotork YT-3100 Скачать руководство пользователя страница 55

Страница: 55 / 68

Smart Positioner

YT-3100

Product Manual

Ver. 1.19

9.11.2

Linear Interpolation (ITP oFF / on)

ITP is used to compensate the linear motion of the actuator into rotary motion of the feedback lever.

Following Auto Calibration, the ITP mode is set automatically to ON when the angle range of the

feedback lever is greater than 20°, but it is set to OFF when this angle is less than 20° or rotary

positioner is used.

The settings below are the process of manually changing the “ITP oFF” to the “ITP on”.

3 seconds

→

Press <UP> or

<DOWN> button

if the above is not

displayed.

Press <UP> or

<DOWN> button

if the above is not

displayed.

→

<ESC>
3 times

→

9.11.3

Lock of Parameters (Write Protect, W UNLOCK / LOCK)

This function is used to set (LOCK) or disable (UNLOCK) the lock for the parameters. Used to prevent

the stored parameters from being changed.

3 seconds

→

Press <UP> or

<DOWN> button

if the above is not

displayed.

Press <UP> or

<DOWN> button

if the above is not

displayed.

→

<ESC>
3 times

→

Содержание YT-3100





































































Результаты поиска

Содержание YT-3100

Отзывы:

Похожие инструкции для YT-3100

Бренды по названию

Популярные бренды

rotork YT-3100, Руководство по эксплуатации продукта

Результаты поиска

Содержание YT-3100

Отзывы:

Похожие инструкции для YT-3100

Бренды по названию

Популярные бренды