rotork YT-3100 Скачать руководство пользователя страница 61

Страница: 61 / 68

Smart Positioner

YT-3100

Product Manual

Ver. 1.19

9.12.4

View Event Log (EVT LOG)

This is used to show the 20 most recent events that occurred in operation. Record 0 is the most recent

of the 20 events and Record 19 is the oldest event. The event detail shows the time when the event

occurred (EVT TIME) as well as the content of the event (EVT INFO). See 9.15 Status and Alarm

Codes for an abbreviation and description of the event details.

3 seconds

→

Press <UP> or

<DOWN> button

if the above is not

displayed.

Press <UP> or

<DOWN> button

if the above is not

displayed.

→

→

<ESC>
4 times

→

Press <UP> or

<DOWN> button

if the above is not

displayed.

The time the event

occurred, 1,013 [sec]

Check the content of

event.

# Event Message Description

The

“SEt on the upper section of screen shows that a specific event has

occurred, while the “CLr” means that the event has been removed. The “TMPH”

displayed on the bottom section indicates an abbreviation for the alarm.

Содержание YT-3100





































































Результаты поиска

Содержание YT-3100

Отзывы:

Похожие инструкции для YT-3100

Бренды по названию

Популярные бренды

rotork YT-3100, Руководство по эксплуатации продукта

Результаты поиска

Содержание YT-3100

Отзывы:

Похожие инструкции для YT-3100

Бренды по названию

Популярные бренды