rotork YT-3100 Скачать руководство пользователя страница 60

Страница: 60 / 68

Smart Positioner

YT-3100

Product Manual

Ver. 1.19

9.12.3

Reset Alarm Status (RST ALRM oFF / on)

The alarm is automatically released when the cause of the alarm is removed. For example, if a high-

temperature alarm is created, the alarm is automatically released when internal temperature drops

below the Temperature High Limit. However, if the Partial Stroke Test fails or Auto Calibration fails, use

this function to release the alarm.

Below is an alarm list that can be released using the RST ALRM function.

Auto Calibration Running

Diagnosis Running

Critical NVM Fail

Non-Critical NVM Fail

PST Fail

Auto Calibration Fail

3 seconds

→

3 seconds

→

Press <UP> or

<DOWN> button

if the above is not

displayed.

Press <UP> or

<DOWN> button

if the above is not

displayed.

→

<ESC>

→

<ESC>
3 times

→

Содержание YT-3100





































































Результаты поиска

Содержание YT-3100

Отзывы:

Похожие инструкции для YT-3100

Бренды по названию

Популярные бренды

rotork YT-3100, Руководство по эксплуатации продукта

Результаты поиска

Содержание YT-3100

Отзывы:

Похожие инструкции для YT-3100

Бренды по названию

Популярные бренды