rotork YT-3100 Скачать руководство пользователя страница 57

Страница: 57 / 68

Smart Positioner

YT-3100

Product Manual

Ver. 1.19

9.11.6

Positioner Self-Test (SELFTEST)

This function is used to diagnose the operation of the memory (RAM or NVM) inside the positioner. If

no error is found during SELFTEST, the SELFTEST menu is displayed after FINISH is displayed, and

if abnormalities are detected, the message "SEt / NVMW" is displayed.

3 seconds

→

Press <UP> or

<DOWN> button

if the above is not

displayed.

Press <UP> or

<DOWN> button

if the above is not

displayed.

→

automatically

→

<ESC>

→

Check the content of

test by pushing the

buttons.

<ESC>
3 times

→

# Diagnostic message

If the abbreviation displayed at the top line is “Set”, it means the event has been

created, and if it is “CLr”, the message has been cleared. NVMW at the bottom is

an alarm message that has occurred. See "9.15 Status and Alarm Code" for alarm

details.

Содержание YT-3100





































































Результаты поиска

Содержание YT-3100

Отзывы:

Похожие инструкции для YT-3100

Бренды по названию

Популярные бренды

rotork YT-3100, Руководство по эксплуатации продукта

Результаты поиска

Содержание YT-3100

Отзывы:

Похожие инструкции для YT-3100

Бренды по названию

Популярные бренды