Ross openGear GPI-8941 Series Скачать руководство пользователя

Страница: 47 / 92

GPI-8941 User Guide (v9.0)

Setting up Remote Control • 47

Verify that the GPI-8941 Card is Available on the Network

Ping the GPI-8941 card using the

Command Prompt

function of your DashBoard client computer. Refer to the

documentation for your client computer for details on using the Command Prompt.

Verify the GPI-8941 RossTalk Client is Configured Correctly

Ensure that the GPI-8941 RossTalk client is configured correctly for your system.

To verify the GPI-8941 RossTalk client is valid

1. Display the GPI-8941 card interface in DashBoard as outlined in “

To access the GPI-8941 in DashBoard

” on

page 35

2. Select the

Remote Control Setup

tab.

3. Select the sub-tab for the RossTalk Client you want to verify.

4. Locate the

Connection Setup

area of the sub-tab.

5. Verify that the

Enable

box is selected.

6. Verify that the destination IP Address specified in the

IP Address

field is correct.

7. Verify that the port address specified in the

TCP Port

field is correct. The default RossTalk port is 7788.

Test the RossTalk Connection

Once you verified the setup as outlined in the previous sections, you may want to test the RossTalk connection
between the GPI-8941 card and the external device.

To test the RossTalk connection

1. Display the GPI-8941 card interface in DashBoard as outlined in “

To access the GPI-8941 in DashBoard

” on

page 35

2. Select the

Remote Control Setup

tab.

3. Select the sub-tab for the RossTalk Client you want to verify.

4. Click

Test Connection

5. Ensure that the

Status

field of the

Remote Control Setup

tab reports the message "

Good

6. If the

Status

field reports an error:

a. Verify that the destination equipment is correctly setup for RossTalk communications.

b. Verify that the destination equipment can be pinged using a Command Prompt.

c. Verify that port 7788 is open on the destination equipment.

Verify that the GPI-8941 Card Can Send GPI Messages

Ensure that the GPI-8941 card is configured to send individual GPI messages. Keep the following in mind:

• The most common configuration is to send when triggered ON.
• The GPI Trigger message setup will send “

GPI <>

”

The

“

” will be replaced with what is in the ID box.

In the below example, GPI 1, 2 and 4 will send messages when triggered on.

Содержание openGear GPI-8941 Series





























































































Результаты поиска

Содержание openGear GPI-8941 Series

Отзывы:

Похожие инструкции для openGear GPI-8941 Series

Бренды по названию

Популярные бренды

Ross openGear GPI-8941 Series, Руководство пользователя

Результаты поиска

Содержание openGear GPI-8941 Series

Отзывы:

Похожие инструкции для openGear GPI-8941 Series

Бренды по названию

Популярные бренды