Ross openGear GPI-8941 Series Скачать руководство пользователя

Страница: 51 / 92

GPI-8941 User Guide (v9.0)

Configuring the GPI Outputs • 51

Configuring the GPI Outputs

This chapter applies if you have the following cards:

• GPI-8941-O16
• GPI-8941-O32
• GPI-8941-I16-O16

Configuring the GPI Outputs

The number of GPI Outputs displayed in the GPI Output Setup tab depends on the card model you are using. The
examples in this section feature the GPI-8941-O32 and the number of outputs on your card may differ from what is
presented here.



If the

GPI All Configuration

box is selected in the

Config

tab, you can change the settings for all GPI Outputs

on the

Setup

tab.

For More Information on...

• the options in the

Setup

tab, refer to the section “

Setup Tab

” on page 65.

• configuring a Timing Window, refer to the section “

Setting up the Vertical Reference Timing Window

” on

page 39.

To configure a GPI Output

1. From the

Tree View

, select the node for the GPI-8941 you want to configure.

2. Select the

GPI Output Setup

tab.

3. Select the

Setup

tab located at the bottom of the

GPI Output Setup

tab.

Содержание openGear GPI-8941 Series





























































































Результаты поиска

Содержание openGear GPI-8941 Series

Отзывы:

Похожие инструкции для openGear GPI-8941 Series

Бренды по названию

Популярные бренды

Ross openGear GPI-8941 Series, Руководство пользователя

Результаты поиска

Содержание openGear GPI-8941 Series

Отзывы:

Похожие инструкции для openGear GPI-8941 Series

Бренды по названию

Популярные бренды