manualshive.com logo in svg

Ross openGear GPI-8941 Series, Руководство пользователя

Поделиться
Скачать
Ross openGear GPI-8941 Series Скачать руководство пользователя страница 42

42 • Setting up Remote Control

GPI-8941 User Guide (v9.0)

5. Use the 

Serial Control

 menu to enable a serial command to change the state of the GPI output connection 

(Allowed) or not (Not Allowed).

6. Repeat steps 1 to 5 for each GPI output connection you want to configure.

Enabling the GPI-8941 for the GPI485 Serial Protocol

Each card includes an RS-485 serial port interface on the rear module. This port enables the card to use the Image 
Video™ GPI485 Serial protocol for control and status reporting.

You must enable serial protocol communication via the options in the Remote Control Setup tab in DashBoard. 
There are two methods for configuring GPI485 serial communications: Standard (using the settings specified by the 
protocol) and Custom. This section outlines both methods.

To enable GPI485 standard serial communications

1. From the 

Tree View

, select the node for the GPI-8941 you want to configure.

2. Select the 

Remote Control Setup 

tab.

3. Select the 

Serial I/O Port

 tab located at the bottom of the 

Remote Control Setup 

tab.

4. Select 

GPI485

 from the 

Protocol

 options.

5. Select the 

Standard Setup

 box in the 

GPI485 Protocol

 area.

• The 

Baud Rate

, 

Data

 

Bits

, 

Parity

, 

Stop Bits

, and 

Tx Driver Control 

settings in the Serial I/O Port Setup 

area are ignored.

• The 

Serial Setup

 field in the 

GPI485 Protocol

 area reports the values that the protocol defines as standard.

To enable GPI485 custom serial communications

1. From the 

Tree View

, select the node for the GPI-8941 card you want to configure.

2. Select the 

Remote Control Setup 

tab.

3. Select the 

Serial I/O Port

 tab located at the bottom of the 

Remote Control Setup 

tab.

4. Select 

GPI485

 from the 

Protocol

 options.

5. Configure the 

Baud Rate

, 

Data

 

Bits

, 

Parity

, 

Stop Bits

, and 

Tx Driver Control 

settings as required for your 

device communicating with the GPI-8941 over the serial port.

Содержание openGear GPI-8941 Series





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды