Ross openGear GPI-8941 Series страница 17 Скачать руководство пользователя

Страница: 17 / 92

GPI-8941 Series User Guide (v9.0)

Hardware Overview • 17

Hardware Overview

This chapter provides an overview of the card-edge controls of the GPI-8941.

Card-edge Controls for the GPI-8941

This section provides information on the jumpers, buttons and LEDs for the GPI-8941. Refer to

Figure 3.1

for the

location of the card-edge features.

Figure 3.1 GPI-8941 — Card Control Locations

Bootload Button

This button for factory service in the unlikely event of a complete card failure. Do not press this button unless
instructed to do so by Ross Technical Support personnel.

Control and Monitoring Features

This section provides information on the card-edge LEDs for the card. Refer to

Figure 3.2

for the location of the

LEDs and controls.

Figure 3.2 Card-edge Controls

Bootload Button

Daughter Card

Bootload Button

PWR LED

ETH LED

CAN LED

RS485 LED

Содержание openGear GPI-8941 Series





























































































Результаты поиска

Содержание openGear GPI-8941 Series

Отзывы:

Похожие инструкции для openGear GPI-8941 Series

Бренды по названию

Популярные бренды

Ross openGear GPI-8941 Series, Руководство пользователя

Результаты поиска

Содержание openGear GPI-8941 Series

Отзывы:

Похожие инструкции для openGear GPI-8941 Series

Бренды по названию

Популярные бренды