manualshive.com logo in svg

Ross openGear GPI-8941 Series, Руководство пользователя

Поделиться
Скачать
Ross openGear GPI-8941 Series Скачать руководство пользователя страница 35

GPI-8941 Series User Guide (v9.0)

Using DashBoard • 35

Using DashBoard

The DashBoard Control System enables you to monitor and control openGear frames and cards from a computer. 
DashBoard communicates with cards in the openGear frame through the MFC-OG3-N or MFC-OGX-N Network 
Controller Card. This controller card is required in order to use DashBoard to monitor the GPI-8941. 

Before You Begin

Before proceeding, ensure that DashBoard software version 6.2.0 or higher is installed on a PC connected to your 
facility network. The DashBoard software and user manual are available from the Ross Video website.

For More Information on...

• using DashBoard, refer to the 

DashBoard User Manual

.

Accessing the GPI-8941 in DashBoard

Ensure that the openGear frame with the GPI-8941 card(s) is displayed in the Tree View located on the left-side of 
the DashBoard window. It may take 30 seconds or more to update the Tree View. Consult the 

MFC-OG3-N and 

MFC-8322-S User Guide 

and 

DashBoard User Manual

 should the Tree View not display the GPI-8941 node.

To launch DashBoard

1. Ensure that you are running DashBoard software version 6.2.0 or higher.

2. Launch DashBoard by double-clicking its icon on your desktop.

To access the GPI-8941 in DashBoard

1. From the 

Tree View

, expand the node for the openGear frame your cards are installed in.

A list of cards installed in the frame displays. 

2. Double-click the node for a card to display its menus in the right-side of the DashBoard window.

In the example below, the node for Frame 6 is expanded to show a list of cards including a GPI-8941-I32 and a 
GPI-8941-O32.

Содержание openGear GPI-8941 Series





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды