background image

Page 58 

 

System configuration  

 

 

 

 

 

© 2017 Ropam Elektronik 

4.  Connect with the module. 
5.  Load the file with the new firmware version. 
6.  Press UPDATE. 

a.  The machine will start the firmware update procedure in the module "BOOT LOADER", 

the procedure should not be interrupted until the message UPDATE COMPLETED. 

b.  if the above procedure ends with an error, repeat the procedure from step 1. 

 

COMMENTS: 
 
- during the procedure can be displayed: 
Error: BasicGSM was not found, Run the bootloader

, then repeat the procedure in point 2 and 

follow the prompts in the BasicGSM Manager.  
 
Ropam Elektronik devices are constantly being developed and expanded with their capabilities and 
functionality. With the new versions of devices, a new version of the configuration program is also 
created. As part of the completion should be provided / compatibility version, or update the software 
(firmware) of all components to the latest version, and use the latest configuration program.  
 
Device updates are available through: 
• BasicGSM Manager → Module → Firmware update (Internet connection required) 
• current CD included with the latest versions, 
• On request, we send any archive file for devices that require compliance. 
 
Updating of BasicGSM Manager is available through: 
• BasicGSM Manager → Help → Check for update (requires internet connection, installer overrides old 
BasicGSM Manager) 
• current CD included with the latest versions. 
 
Updating the USB cable driver is available through: 
• BasicGSM Manager (option for installing software: install USB drivers), 
• FTDI manufacturer's website → http://www.ftdichip.com/Drivers/VCP.htm. 
 

System configuration: SMS commands. 

Functionality of the module allows to change the selected configuration parameters remotely. This is 
done by sending an SMS with the appropriate command (command) with the access code. After the 
correct programming procedure, the module will reply to the SMS: "Configuration changed" in the case 
of configuration error, the reply is: "Error in configuration message, send correct again!"  
check the format of the SMS, then correct the content and resubmit. The factory set parameters: 
 
SMS code / application login: 1111 
Sending SMS control confirmation 
PIN code request disabled 
 
 
 
 
 
 
 
 

Содержание BasicGSM 2




















































































Отзывы: