manualshive.com logo in svg

RollSeal RS-500 Series, Руководство по установке

Поделиться
Скачать
RollSeal RS-500 Series Скачать руководство пользователя страница 5

 

 

Part No 4801-5154 Rev 01-2017 

RS-500/600 Series Doors 

 Page 5 

Danger! 

Only Qualified Electrical Personnel Familiar With The Construction And Operation Of This 

Equipment And The Hazards Involved Should Install, Adjust, And/Or Service This Equipment.  

Read And Understand This Manual In Its Entirety Before Proceeding.   

Failure To Observe This Precaution Could Result In Severe Bodily Injury Or Death!

 

 

Warning! 

                     

 

 

 

IMPORTANT INSTALLATION INSTRUCTIONS 

Warning! 

To Reduce The Risk Of Severe Injury Or Death: 

1.  READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS. 

2.  Do not connect the door operator to the source of power until instructed to do so. 

3.  Locate the control station: (a) within sight of the door, (b) at a minimum height of 5 feet 

so small children cannot reach it, and (c) away from all moving parts of the door. 
Remove all ropes and remove or make inoperative all locks connected to the garage 
door before installing opener. 

4.  For products having a manual release, instruct the end user on the operation of the 

manual release. Where possible, install the door opener 8 feet or more above the floor. 
For products having an emergency release, mount the emergency release within reach, 
but at least 6 feet above the floor and avoiding contact with vehicles to avoid accidental 
release. 

!

Item 4501-6312 

(Warning Moving Door Label) 

Supplied With Door, 

MUST Be Installed 

On Inside Of Cooler/Freezer 

Beside Door Opening.

 

 

!

 

!

 

!

 

Содержание RS-500 Series





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды