manualshive.com logo in svg

RollSeal RS-500 Series, Руководство по установке

Поделиться
Скачать
RollSeal RS-500 Series Скачать руководство пользователя страница 23

 

 

Part No 4801-5154 Rev 01-2017 

RS-500/600 Series Doors 

 Page 23 

 

 

  

NOTE: The vertical members should 

be aligned so that their outer 
flanges will exactly overlap 
with the framing boards or 
posts when the door 
assembly is raised into 
position. 

 

4.

 

Assemble workers and 
equipment into position on 
each side of the door assembly.   

 

IMPORTANT: SLOWLY LIFT TOP 

OF DOOR ASSEMBLY TO 
RAISE THE DOOR.  See 
Diagram 13G. 

 
 
 

Diagram 13H 

 

 
 
 
 
 
 
 
 
 

 

 

 

 

 

 

5.   Lean door assembly upright against clear opening. 

6.  Carefully press flanges of the door assembly flush against faces of framing boards or posts.  

7.  Fasten Tek screws (in steel) or lag screws (in wood) through the flanges on sides of door assembly.  

Securely tighten all screws. 

8.  On the lower and upper flanges of the horizontal member there are attachment points for fastening 

screws.  Fasten Tek screws (in steel) or lag screws (in wood) through the holes.  This secures the top of 
the door to the clear opening. 

9.  Locate the two floor mounting holes at the bottom of the left and right tracks.  

See Diagram 13H

.  

10.  Drill a 1/4" hole and install Hammer Set Anchors (1002-6030) in both right and left tracks.  See 

Diagram 13H. 

11.  This completes fastening of the door assembly to the clear opening. 

Содержание RS-500 Series





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды