RollSeal RS-500 Series Скачать руководство пользователя страница 49

Страница: 49 / 68

Part No 4801-5154 Rev 01-2017

RS-500/600 Series Doors

Page 49

NOTE: The Release for the
Cam Buckle is located on
the panel side of the
Buckle. This view shows
the Cam Buckle as see
from the front of the door.

33.3

Resetting (Closing) The Door

After the RollSeal RS-500 Door is opened by using the Emergency Egress Strap, the door must be carefully
re-set to ensure proper operation in the future.

Firmly hold strap. See

Diagram 33F.

Press the Cam Buckle Release. See

Diagram 33G.

Gradually feed strap through Cam Buckle until door is closed at bottom and D-ring is in the
position shown in

Diagram 33E

Return Emergency Egress Tool to retainer for future use.

Cycle the door up and down in normal operating mode to ensure proper re-setting of the door.
Adjust if necessary. Door should now function normally.

Diagram 33E

CAUTION!

When the Cam Buckle is released, the door will rapidly close unless tension is held on the strap.
Keep fingers away from buckle while closing.

Firmly
hold
strap.

Cam
Buckle

Egress
Strap

D-ring

Egress
Tool

Cam Buckle
Release

NOTE: This view
shows the Cam
Buckle as seen
from the back of
the door when the
Egress Strap has
not been pulled.

Содержание RS-500 Series





































































Результаты поиска

Содержание RS-500 Series

Отзывы:

Бренды по названию

Популярные бренды

RollSeal RS-500 Series, Руководство по установке

Результаты поиска

Содержание RS-500 Series

Отзывы:

Бренды по названию

Популярные бренды