RollSeal RS-500 Series Скачать руководство пользователя страница 4

Страница: 4 / 68

Page 4

RS-500/600 Series Doors

Part No 4801-5154 Rev 01-2017

Warnings (Avertissements)

Warning!

Disconnect All Power Sources Before Installing This Equipment. Failure To Disconnect

Power Source Can Result In Property Damage, Serious Injury Or Death!

Warning!

Dangerous Rotating Machinery!

Keep Hands, Clothing, Etc. Clear When Operating!

Do Not Operate Without All Guards And Covers In Place!

Warning!

All Wiring Should Be In Accordance with National Electrical Codes Or Other Local Codes.

Warning!

The Installer Is Responsible For Complying With All Relevant Regulations,

Such As National Wiring Regulations And Accident Prevention Regulations.

Particular Attention Must Be Given To The Cross-sectional Areas Of Conductors, The

Selection Of Fuses Or Other Protection, And Protective Earth/Ground Connections!

Warning!

The Voltages In The Power Cables And Certain Parts Of The Drive Can Result In Death.

Whenever The Drive Has Been Used, It Must Be Isolated And Disconnected

For 5 Minutes Before Any Work Commences.

Содержание RS-500 Series





































































Результаты поиска

Содержание RS-500 Series

Отзывы:

Бренды по названию

Популярные бренды

RollSeal RS-500 Series, Руководство по установке

Результаты поиска

Содержание RS-500 Series

Отзывы:

Бренды по названию

Популярные бренды