manualshive.com logo in svg

RollSeal RS-500 Series, Руководство по установке

Поделиться
Скачать
RollSeal RS-500 Series Скачать руководство пользователя страница 44

 

 

Page 44 

RS-500/600 Series Doors 

 Part No 4801-5154 Rev 01-2017 

28

 

Door Panel Adjustments 

During normal operation, the tension pipes should run in close proximity of each other.  The clearance between the 
tension pipes should normally be between 1/4

 to 1/2

 (6.35 mm - 12.7 mm).  See Detail 3 below. There are two 

situations pertaining to the tension pipes that may cause problems with door operation.  If the tension pipes are too 
far apart, the tension pipes will not repel each other.  This causes poor contact between the hook & loop or 
magnets.  On the other hand, if the tension pipes are riding one another (i.e. touching one another), the door panel 
material does not flow evenly, thus leaving wrinkles in the panel instead of a stretched, smooth & even appearance. 

 

Adjustment Procedures 

The clearance between the tension pipes can be adjusted by raising or lowering the door panels.  Each door has three 
panels:  (1) the inside panel (panel facing the inside of building) is attached to the back plate.  (2) The center panel is 
attached to the roller.  (3) The outside panel (facing the outside of building) is attached to the front bar.  Adjustments 
are made to the inside panel and/or the outside panel. 

NOTE:  The door must be in the closed position for panel adjustments.  Ensure the 

panels are not damaged while removing or reinstalling the nuts and screws. 

To adjust the height of the outside tension pipe, raise or lower the outside door panel by detaching the panel hook & 
loop from the front bar, and raising or lowering the panel.  Then re-attach the panel loop to the hook on the front bar.  
Be sure to keep the tension pipe level during this procedure. 
To adjust the height of the inside tension pipe, raise or lower the inside door panel by detaching the panel hook & 
loop from the back plate, and raising or lowering panel.  Then re-attach the panel loop to the hook on back plate.  Be 
sure to keep tension pipe level during this procedure.  Install Tek screws through the panel material and into the 
back plate to securely hold the material in place. 
 
 
 

 

 

Содержание RS-500 Series





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды