manualshive.com logo in svg

RollSeal RS-500 Series, Руководство по установке

Поделиться
Скачать
RollSeal RS-500 Series Скачать руководство пользователя страница 36

 

 

Page 36 

RS-500/600 Series Doors 

 Part No 4801-5154 Rev 01-2017 

20.1

 

Tools Required 

 

3/8 in. (10 mm) Power screwdriver (portable) 
3/16 in. (5 mm) Drill bit and power drill 

3/8 x 1 in. Bolts and nuts (supplied) 

Socket 
Hammer 
Tape measure 
Carpenter's level 

NOTE: Other Tools May Be Required According To Installation. 

 

20.2

 

Overview 

The RS-500/600 Freezer Door is shipped with pre-assembled vertical members (left track and right tracks), 
with floating magnets, and a pre-assembled horizontal member (head unit).  When components are received, 
check for damaged, loose or missing parts.  If there are damaged or missing parts contact your RollSeal 
distributor immediately.  Please read and understand all instructions in this manual before beginning 
installation. After the door has been assembled and attached to the door framing per instructions in 

Section 

13, Page 18

 of this manual it is necessary to install the Condensation Management System (CMS) and ducts 

to complete the freezer door installation. 
 
 

21

 

Installation of Condensation  
Management System and Ducts 

Install the Condensation Management 
System at the top of the Freezer Door 
approximately in the center of the door as 
shown below.  Install the 5/7” Duct 
Adaptor in the intake side of the 
Condensation Management System.  
Carefully run the duct work to the two 
couplings on the left and right track of 
the door. Fasten each end of the duct with 
hose Clamps.   
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

NSF Certified Doors are equipped 

with Left mount Brother operators, 

Smart Controller, and Magnetic 

Track Sealing System 

Содержание RS-500 Series





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды