Roland GT-8 Скачать руководство пользователя страница 17

Страница: 17 / 108

Chapter 2 Creating Your Own Favorite Tones (Patches)

Chapter

Switching the Bank and Number

fig.02-070

Press a BANK pedal.

The bank switches, then the indicator for the numbered
pedal that was active before the BANK pedal was
pressed starts flashing, indicating that the GT-8 is ready
for selection of the patch number (at this stage, however,
the patch is not switched yet).

Select the number of the patch you want to switch to by
pressing the corresponding number pedal.

The indicator for the selected number pedal lights up,
and the GT-8 switches to that patch.

If the Patch Does Not Switch

On the GT-8, you cannot switch patches in any screen other
than the Play screen. Press [EXIT] to return to the Play screen
(p. 14).

Adjusting the Tones with the Knobs

The GT-8 panel features fifteen knob controls. These knobs
let you make adjustments or changes to the selected patch’s
tone quickly and easily.

fig.02-080

When you want to save a tone created with the knob
controls, proceed as described in “Storing Patches (Patch
Write)” (p. 22).
If the power is turned off, or if the tone is switched
(Patch Change; p. 16) before you’ve carried out the Write
procedure, the newly created tone will be discarded.

* If you want to name the patch or edit the name, proceed to

“Naming Patches (Patch Name)” (p. 21) before you save.

Knob

Explanation

PREAMP/SPEAKER

TYPE

Selects the preamp type.

* After pressing [TYPE VARIATION], you can select variations by

turning the knob to the type you want.

GAIN

Adjusts the degree of preamp distortion.
The distortion gets stronger as the knob is
turned to the right.

BASS

Adjusts the sound quality of the preamp’s
low-frequency range. The low frequencies
are boosted as the knob is turned to the right.

MIDDLE

Adjusts the sound quality of the preamp’s
midrange. The midrange frequencies are
boosted as the knob is turned to the right.

TREBLE

Adjusts the sound quality of the preamp’s
high-frequency range. The high frequencies
are boosted as the knob is turned to the right.

PRESENCE

Adjusts the sound quality of the preamp’s
Ultra-high-frequency range. The high fre-
quencies are boosted as the knob is turned
to the right.

LEVEL

Adjusts the preamp volume level. The volume
increases as the knob is turned to the right.

OVERDRIVE/DISTORTION

TYPE

Selects the type of overdrive or distortion.

* After pressing [TYPE VARIATION], you can select variations by

turning the knob to the type you want.

DRIVE

Adjusts the degree of overdrive or distor-
tion. The distortion appears stronger as the
knob is turned to the right.

LEVEL

Adjusts the overdrive/distortion volume
level. The volume increases as the knob is
turned to the right.

DELAY

FEEDBACK

Adjusts the number of times the delay is re-
peated. The number of repeats increases as
the knob is turned to the right.

LEVEL

Adjusts the volume level of the delay sound.
The delay sound increases as the knob is
turned to the right.

CHORUS

LEVEL

Adjusts the volume level of the chorus
sound. The chorus sound increases as the
knob is turned to the right.

REVERB

LEVEL

Adjusts the volume level of the reverb
sound. The reverb sound increases as the
knob is turned to the right.

PATCH LEVEL

Adjusts the overall volume level. The volume increases as the knob
is turned to the right.

GT-8_e.book 17 ページ２００７年６月２９日　金曜日　午後３時５５分

Содержание GT-8













































































































Результаты поиска

Содержание GT-8

Отзывы:

Похожие инструкции для GT-8

Бренды по названию

Популярные бренды

Roland GT-8, Руководство пользователя

Результаты поиска

Содержание GT-8

Отзывы:

Похожие инструкции для GT-8

Бренды по названию

Популярные бренды