manualshive.com logo in svg

ROHS MC9S08QE128, Справочное руководство

ROHS MC9S08QE128 - это продукт высочайшего качества, который обеспечивает надежное и эффективное функционирование вашего устройства. Вы можете скачать бесплатно Reference Manual и другие руководства по эксплуатации на manualshive.com. Познакомьтесь с функционалом этого устройства и улучшите свой опыт использования с помощью нашего руководства.

Поделиться
Скачать
background image

Chapter 8 Central Processor Unit (S08CPUV4)

MC9S08QE128 MCU Series Reference Manual, Rev. 2

150

Freescale Semiconductor

8.3.4

Direct Addressing Mode (DIR)

In direct addressing mode, the instruction includes the low-order eight bits of an address in the direct page
(0x0000–0x00FF). During execution a 16-bit address is formed by concatenating an implied 0x00 for the
high-order half of the address and the direct address from the instruction to get the 16-bit address where
the desired operand is located. This is faster and more memory efficient than specifying a complete 16-bit
address for the operand.

8.3.5

Extended Addressing Mode (EXT)

In extended addressing mode, the full 16-bit address of the operand is located in the next two bytes of
program memory after the opcode (high byte first).

8.3.6

Indexed Addressing Mode

Indexed addressing mode has seven variations including five that use the 16-bit H:X index register pair and
two that use the stack pointer as the base reference.

8.3.6.1

Indexed, No Offset (IX)

This variation of indexed addressing uses the 16-bit value in the H:X index register pair as the address of
the operand needed to complete the instruction.

8.3.6.2

Indexed, No Offset with Post Increment (IX+)

This variation of indexed addressing uses the 16-bit value in the H:X index register pair as the address of
the operand needed to complete the instruction. The index register pair is then incremented
(H:X = H:X + 0x0001) after the operand has been fetched. This addressing mode is only used for MOV
and CBEQ instructions.

8.3.6.3

Indexed, 8-Bit Offset (IX1)

This variation of indexed addressing uses the 16-bit value in the H:X index register pair plus an unsigned
8-bit offset included in the instruction as the address of the operand needed to complete the instruction.

8.3.6.4

Indexed, 8-Bit Offset with Post Increment (IX1+)

This variation of indexed addressing uses the 16-bit value in the H:X index register pair plus an unsigned
8-bit offset included in the instruction as the address of the operand needed to complete the instruction.
The index register pair is then incremented (H:X = H:X + 0x0001) after the operand has been fetched. This
addressing mode is used only for the CBEQ instruction.

8.3.6.5

Indexed, 16-Bit Offset (IX2)

This variation of indexed addressing uses the 16-bit value in the H:X index register pair plus a 16-bit offset
included in the instruction as the address of the operand needed to complete the instruction.

direct "page": Not in the sense of MMU 8 pages

Содержание MC9S08QE128


























































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MC9S08QE128

2M Technology 2MTHFR-2M Quick Manual preview
2MTHFR-2M
Бренд: 2M Technology Страницы: 17
2iB SC10 Quick Start Manual preview
SC10
Бренд: 2iB Страницы: 5
e-BLEACH infinity User Manual preview
infinity
Бренд: e-BLEACH Страницы: 24
Taco Electronic Solutions iWorx MPU2 Installation Manual preview
iWorx MPU2
Бренд: Taco Electronic Solutions Страницы: 28
Purmo NC 24 V Assembly Instructions preview
NC 24 V
Бренд: Purmo Страницы: 2
salmson ACSON VARIO Installation And Starting Instructions preview
ACSON VARIO
Бренд: salmson Страницы: 78
D+H DXD 150-BSY+ Original Instructions Manual preview
DXD 150-BSY+
Бренд: D+H Страницы: 16
PENKO 1020 CAN-RS232-RS422 MFL Manual preview
1020 CAN-RS232-RS422 MFL
Бренд: PENKO Страницы: 29
Nuvoton NuMicro M252 Series User Manual preview
NuMicro M252 Series
Бренд: Nuvoton Страницы: 38
Woodward ProAct III Installation And Operation Manual preview
ProAct III
Бренд: Woodward Страницы: 32
SystemAir SYSVRF AHU 10HP S Installation & Owner'S Manual preview
SYSVRF AHU 10HP S
Бренд: SystemAir Страницы: 16
Zapi COMBI SEM-1 Operating And Users Manual preview
COMBI SEM-1
Бренд: Zapi Страницы: 30
HANYOUNG NUX TPR-3SL-EP Instruction Manual preview
TPR-3SL-EP
Бренд: HANYOUNG NUX Страницы: 4
QUANT QUANT-14 Operation Manual preview
QUANT-14
Бренд: QUANT Страницы: 24
Walchem WDIS Series Instruction Manual preview
WDIS Series
Бренд: Walchem Страницы: 35
AL-KO UP4 Translation Of The Original Installation Instructions preview
UP4
Бренд: AL-KO Страницы: 52
Belimo SM24A-S Technical Data Sheet preview
SM24A-S
Бренд: Belimo Страницы: 4
Oilon VSi 6-14 Installation And Operation Manual preview
VSi 6-14
Бренд: Oilon Страницы: 74

Бренды по названию

Популярные бренды

Загрузить еще бренды