ROHS MC9S08QE128 Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 345

background image

Chapter 4 Memory

MC9S08QE128 MCU Series Reference Manual, Rev. 2

Freescale Semiconductor

85

4.6.3.3

Illegal Flash Operations

4.6.3.3.1

Flash Access Violations

The FACCERR flag will be set during the command write sequence if any of the following illegal steps
are performed, causing the command write sequence to immediately abort:

1. Writing to a flash address before initializing the FCDIV register.

2. Writing to any flash register other than FCMD after writing to a flash address.

3. Writing to a second flash address in the same command write sequence.

4. Writing an invalid command to the FCMD register unless the address written was in a protected

area of the flash array.

5. Writing a command other than burst program while FCBEF is set and FCCF is clear.

6. When security is enabled, writing a command other than mass erase to the FCMD register when

the write originates from a non-secure memory location or from the background debug mode.

7. Writing to a flash address after writing to the FCMD register.

8. Writing to any flash register other than FSTAT (to clear FCBEF) after writing to the FCMD register.

9. Writing a 0 to the FCBEF flag in the FSTAT register to abort a command write sequence.

The FACCERR flag will also be set if the MCU enters stop mode while a program or erase operation is
active. The operation is aborted immediately and, if burst programming, any pending burst program
command is purged (see

Section 4.6.4.2, “Stop Mode”

).

The FACCERR flag will not be set if any flash register is read during a valid command write sequence.

If the flash memory is read during execution of an algorithm (FCCF = 0), the read operation will return
invalid data and the FACCERR flag will not be set.

If the FACCERR flag is set in the FSTAT register, the user must clear the FACCERR flag before starting
another command write sequence (see

Section 4.6.2.5, “Flash Status Register (FSTAT)”

).

4.6.3.3.2

Flash Protection Violations

The FPVIOL flag will be set after the command is written to the FCMD register during a command write
sequence if any of the following illegal operations are attempted, causing the command write sequence to
immediately abort:

1. Writing the program command if the address written in the command write sequence was in a

protected area of the flash array.

2. Writing the sector erase command if the address written in the command write sequence was in a

protected area of the flash array.

3. Writing the mass erase command while any flash protection is enabled.

4. Writing an invalid command if the address written in the command write sequence was in a

protected area of the flash array.

If the FPVIOL flag is set in the FSTAT register, the user must clear the FPVIOL flag before starting another
command write sequence (see

Section 4.6.2.5, “Flash Status Register (FSTAT)”

).

«
...
83
84
85
86
87
...
»

Содержание MC9S08QE128


























































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MC9S08QE128

Бренд: Zeagle Страницы: 37

Extra Free RZB-02

Бренд: Zamel Страницы: 2

Бренд: Sullair Страницы: 31

Бренд: EpiSensor Страницы: 37

Sundstrom SR307

Бренд: S.E.A. Group Страницы: 5

Бренд: H3C Страницы: 16

Бренд: Zander Aachen Страницы: 75

Бренд: zeeltronic Страницы: 15

Бренд: M-system Страницы: 3

ADAP-KOOL AK-PC 781

Бренд: Danfoss Страницы: 142

Alicat Scientific MC

Бренд: Halma Страницы: 2

Бренд: Sorel Страницы: 20

Бренд: Computherm Страницы: 40

Бренд: Advanced Control Technologies Страницы: 3

Бренд: VAL Страницы: 10

Бренд: Zonet Страницы: 2

Бренд: National Instruments Страницы: 20

Бренд: Eliweli Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды