manualshive.com logo in svg

ROHS MC9S08QE128, Справочное руководство

ROHS MC9S08QE128 - это продукт высочайшего качества, который обеспечивает надежное и эффективное функционирование вашего устройства. Вы можете скачать бесплатно Reference Manual и другие руководства по эксплуатации на manualshive.com. Познакомьтесь с функционалом этого устройства и улучшите свой опыт использования с помощью нашего руководства.

Поделиться
Скачать
background image

Internal Clock Source (S08ICSV3)

MC9S08QE128 MCU Series Reference Manual, Rev. 1.11

214

Freescale Semiconductor

In FLL bypassed external mode, the ICSOUT clock is derived from the external reference clock. The FLL
clock is controlled by the external reference clock, and the FLL loop will lock the FLL frequency to the
FLL factor times the external reference frequency, as selected by the RDIV bits, so that the ICSLCLK will
be available for BDC communications, and the external reference clock is enabled.

11.4.1.6

FLL Bypassed External Low Power (FBELP)

The FLL bypassed external low power (FBELP) mode is entered when all the following conditions occur:

•

CLKS bits are written to 10.

•

IREFS bit is written to 0.

•

BDM mode is not active and LP bit is written to 1.

In FLL bypassed external low power mode, the ICSOUT clock is derived from the external reference clock
and the FLL is disabled. The ICSLCLK will be not be available for BDC communications. The external
reference clock is enabled.

11.4.1.7

Stop

Stop mode is entered whenever the MCU enters a STOP state. In this mode, all ICS clock signals are static
except in the following cases:

ICSIRCLK will be active in stop mode when all the following conditions occur:

•

IRCLKEN bit is written to 1

•

IREFSTEN bit is written to 1

ICSERCLK will be active in stop mode when all the following conditions occur:

•

ERCLKEN bit is written to 1EREFSTEN bit is written to 1

•

11.4.2

Mode Switching

The IREF bit can be changed at anytime, but the actual switch to the newly selected clock is shown by the
IREFST bit. When switching between FLL engaged internal (FEI) and FLL engaged external (FEE)
modes, the FLL will begin locking again after the switch is completed.

The CLKS bits can also be changed at anytime, but the actual switch to the newly selected clock is shown
by the CLKST bits. If the newly selected clock is not available, the previous clock will remain selected.

The DRS bits can be changed at anytime except when LP bit is 1. If the DRS bits are changed while in
FLL engaged internal (FEI) or FLL engaged external (FEE), the bus clock remains at the previous DCO
range until the new DCO starts. When the new DCO starts the bus clock switches to it. After switching to
the new DCO the FLL remains unlocked for several reference cycles. Once the selected DCO startup time
is over, the FLL is locked. The completion of the switch is shown by the DRST bits.

Содержание MC9S08QE128


























































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MC9S08QE128

Harmonic Drive CHA Engineering Data preview
CHA
Бренд: Harmonic Drive Страницы: 85
Maguire Products GRAVIMETRIC AUGER FEEDER MGF-ST Instruction Manual preview
GRAVIMETRIC AUGER FEEDER MGF-ST
Бренд: Maguire Products Страницы: 47
Magtrol DSP7000 User Manual preview
DSP7000
Бренд: Magtrol Страницы: 160
National Instruments PXI-8231 Installation Manual preview
PXI-8231
Бренд: National Instruments Страницы: 6
Eaton EZD Series User Manual preview
EZD Series
Бренд: Eaton Страницы: 448
NOCO Genius CURTIS DC Series Installation Instruction preview
CURTIS DC Series
Бренд: NOCO Genius Страницы: 2
Xylem Aquavar AB2 Quick Start Manual preview
Aquavar AB2
Бренд: Xylem Страницы: 2
Dungs 273061 Instructions Manual preview
273061
Бренд: Dungs Страницы: 56
Emec PH CONTROLLER Operating Manual preview
PH CONTROLLER
Бренд: Emec Страницы: 8
BQT BioX Series Installation Manual preview
BioX Series
Бренд: BQT Страницы: 2
Neets Control LiMa Installation Manual preview
LiMa
Бренд: Neets Control Страницы: 12
Instrutech VGC301 User Manual preview
VGC301
Бренд: Instrutech Страницы: 42
Texas Instruments LaunchPad LP-CC1352P7-1 Manual preview
LaunchPad LP-CC1352P7-1
Бренд: Texas Instruments Страницы: 3
KELD KLT11IB Specification And Operating Instructions preview
KLT11IB
Бренд: KELD Страницы: 2
Taconova Tacosol Load EXA L Manual preview
Tacosol Load EXA L
Бренд: Taconova Страницы: 40
Zamel exta life SRM-22 Operation Manual preview
exta life SRM-22
Бренд: Zamel Страницы: 5
Omega Engineering Wireless Meter Scanner & Controller wi... User Manual preview
Wireless Meter Scanner & Controller wi...
Бренд: Omega Engineering Страницы: 96
Greengate ControlKeeper 2 CK2-120-NC Installation Sheet preview
ControlKeeper 2 CK2-120-NC
Бренд: Greengate Страницы: 7

Бренды по названию

Популярные бренды

Загрузить еще бренды