Rohde & Schwarz 1157.3458.02 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 80

Rohde & Schwarz 1157.3458.02 Скачать руководство пользователя страница 51

R&S FSH-K1

Command Description

1157.3564.12 45

E-8

LIMCHKREMOTE (Limit Check Remote Message)

This command enables the remote message (frequency/c level) on limit check and/or on
threshold limit fail. The instrument will send a message (frequency/channel and level) every time the
limit is exceeded.

Value

Limit Check Remote

0

OFF

1

Limit Check – Remote message on
fail

Example:

get<cr>

0<cr>

limchkremote,1<cr>

‘enable remote massage on limit fail

0<cr>

‘responds parameter ok

123.456E6,23.5<cr>

‘limit

exceeded

130.567E6,22.0<cr>

‘limit

exceeded…..

…

0<cr>

‘remote message on limit fail OFF

THRLOW (Lower Threshold Line)

This command defines the lower threshold line (value). The unit of the threshold value is specified with
the Unit parameter. This command is available in Receiver / Scan Mode only.

Example:

set<cr>

0<cr>

thrlow,30<cr>

‘specifies lower threshold line to -30 dBuV

0<cr>

‘responds parameter ok

THRUPP (Upper Threshold Line)

This command defines the upper threshold line (value). The unit of the threshold value is specified with
the Unit parameter. Available in Receiver / Scan Mode only.

Example:

set<cr>

0<cr>

thrupp,70<cr>

‘specifies upper threshold line to 70 dBuV

0<cr>

‘responds parameter ok

THRPASS (Threshold Line Passed Query)

This command returns the threshold line check status. Available in Receiver / Scan Mode only.

Value

Threshold Line Check

0

Unkown

1

Failed

2

Passed

Example:

get<cr>

0<cr>

thrpass<cr>

‘query threshold line check

0<cr>

‘responds parameter ok

2

‘threshold check passed

«
...
49
50
51
52
53
...
»

Содержание 1157.3458.02

















































































Отзывы:

Нет отзывов