Rohde & Schwarz 1157.3458.02 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 80

Rohde & Schwarz 1157.3458.02 Скачать руководство пользователя страница 41

R&S FSH-K1

Command Description

1157.3564.12 35

E-8

DELTAON (Delta Multimarker On)

This command turns the corresponding deltamarker on / off. DELTAON,1 is used for the deltamarker in
normal and in multi marker mode. DELTAON,2 to DELTAON,6 are available in multi marker mode only

Param 1

Param 2

Value

Deltamarker No

Value

Deltamarker

0

OFF

1…6 Deltamarker

1…6

1

ON

Example:

set<cr>

0<cr>

deltaon,2,1<cr>

‘turns deltamarker 2 on

0<cr>

‘responds parameter ok

DELTA (Delta Multimarker)

This command sets the corresponding deltamarker to the specified position in relation to the marker or
queries the current deltamarker value.
The deltamarker unit depends on the unit of the x-axis which can be Hz, seconds or meter/feet
depending of the measurement mode. The unit of the second value in the GET command response
depends on the current unit of the y-axis.
If Smith Chart is active, the second and third values are the complex impedance.

Value

Deltamarker

2…6 Deltamarker

2…6

DELTA,2 is used for the deltamarker in normal and multi marker mode, DELTA,3 to DELTA,6 are
available in multi marker mode only.

Example:

set<cr>

0<cr>

delta,2,-100E3<cr>

‘set deltamarker 2 to 100 kHz below the marker

0<cr>

‘responds parameter ok

Example 2:

get<cr>

0<cr>

delta,2<cr>

‘query delta marker 2 value

0<cr>

‘responds parameter ok

-100e3,-8.23<cr>

‘returns deltamarker frequency and relative level

MARKALLON (All Multimarker On)

This command turns all multimarker on / off. This command is available in multi marker mode only.

Value

All Marker

0

OFF

1

ON

Example:

set<cr>

0<cr>

markallon,1<cr>

‘turns all multi marker on

0<cr>

‘responds parameter ok

«
...
39
40
41
42
43
...
»

Содержание 1157.3458.02

















































































Отзывы:

Нет отзывов