25
digit”, select one of the [01] to [45], [49], [50], [51] to [54], [60] or [61] “master user’s
submenus”
.
To enter each “master user’s submenu” the master user should enter 2 digits which are
corresponding to the order number of each submenu (i.e. for submenu no. 9 press [0] and [9] keys).
After entering the 2 digits corresponding to the order number of one submenu, the keypad buzzer will
beep for 3 times, confirming the system is being within respective submenu.
Once the system was entering one of the “master user’s submenus”, the keypad LEDs’ status will be as
follows:
Remarks:
ARMED A LED
ON
SYSTEM LED
Blinking
READY LED
ON
zone 1, 2 and 3 LEDs
Blinking
That means the selected user code, the follow me phone number or the system
time and date
were programmed
during a previous programming session.
Only zone 1 LED
Blinking
That means the selected user code, the follow me phone number or the system
time and date
are not programmed
and
the control panel is waiting for the
first digit group
for respective option.
P
ROGRAMMING
/
S
ELECTIVE
E
RASURE (
EXCEPT THE
“
MASTER CODE
”) OF
01
TO
45
U
SER
C
ODES
[*
][
7
][
Master Code]
or
[CODE
][
Master Code],
where [CODE] is the key labeled “CODE”
The [*][7][Master Code] or [CODE][Master Code] commands allow to the “master user” to modify all
the user codes, except the installer’s codes.
While the system is being within “master user’s programming menu”,
in order to program/erase
any of 01 to 45
user codes
, the master user should select the corresponding submenu from
[01] to [45],
by pressing the 2-digit order number of the user code to be programmed/erased
(i.e.
while the system is being within “master user’s programming menu”,
for user code no. 15 press [1]
and [5] keys).
Then enter the following sequence
:
[x
][
x
][
x
][
x]
(or
[x
][
x
][
x
][
x
][
x
][
x]
for 6-digit codes)
|RIGHTS
1
||#|| RIGHTS
2
||#|
where [x][x][x][x] and [x][x][x][x][x][x] are the new 4 or 6 digits for the “selected user code” and
RIGHTS
1
& RIGHTS
2
are 1&2 sets of rights for selected user code.
While the system is being within programming
/erasing session of the “selected user code”, the keypad LEDs’
status will be as follows:
Keypad LEDs:
LEDs’ Status:
Remarks:
ARMED A LED
ON
SYSTEM LED
Blinking
READY LED
ON
Zone 1, 2 and 3 LEDs Blinking
That means the
“selected user code”
was programmed
during a previous programming
session.
Only zone 1 LED
Blinking
That means the
“selected user code”
isn’t programmed
and
the control panel is
waiting for the first digit
for the new value of the “selected user code”.
One of the 2 to 4
zone LEDs
(or to 6,
for 6-digit codes)
Blinking
That means the
“selected user code”
is programming
and
the control panel is
waiting for the corresponding digit
for the new value of the “selected user code”.
1. Programming/Erasing of the “selected user code” may be skipped by [#] key pressing.
1.1
After [#] key pressing, if the
“
selected user code
”
was programmed during a previous
programming session, then the keypad buzzer will sound 3 confirmation beeps and the system will
pass to display the first 5 rights of the
“
selected user code
”
(step no. 3).
