Robe ColorSpot 2500E AT, Руководство пользователя

Страница: 29 / 40

2
Lamp Presetting - Select this menu to change the lamp „behaviour”.
Lamp On/Power On
- Select this function to turn the lamp on automatically after switching the fixture on.
Lamp Off via DMX - Select this function to switch off the lamp via DMX.
Lamp On if DMX Present - This function allows you to strike the lamp automatically after 2 seconds if DMX
signal is present on the data link.If the ignition is unsuccessfull (e.g.lamp is too hot), the fixture will try to ignite
the lamp after next 2 s. This process will repeat until the lamp lights.
Lamp Off if not DMX
- This function allows you to switch Off the lamp automatically after 2 minutes if DMX signal
is missing on the data link.
Lamp Ignition Delay - This function allows you to set the time delay( 0-0s) before the lamp will be ignited. This
setting will not affect starting the lamp direct from the control panel (menu "Lamp On/Off").
Lamp Light Sensor - Select this function to switch the lamp light sensor on or off. The option „On” is for the standard
operation.
Important: The option „Off” is for „emergency operation” only if the lamp light sensor is defective and you will wait for
a service intervertion! If the lamp light sensor is switched off and at switching the lamp on the electronics will still try to
ignite the lamp until it shines (even when the lamp is damaged or absent), on this account some electronics parts could
be damaged!
Display Adjusting
- This function allows you to change the display settings.
Display Permanent On - This function allows you to keep the display on or to turn off automatically 2 minutes
after last pressing any button(or a wheel movement) on the control panel.
Display Intensity - Select this function to adjust the display intensity (1-min.,10-max.).
Display Backlight
- Select this function to adjust the display backlight (1-min.,10-max.).
Display Turned - Select this function to turn the display by 10°.
Blackout d.M.C. - Select this function to enable the blackout during the head movement correction (if the moving head
lost its right pan/tilt position for a short moment).
Pan/Tilt Feedback - This function allows to return the mowing head to the required pan/tilt position after changing the
position by external force (e.g.by stroke).
Be careful, the Pan/Tilt Feedback OFF is not the standard operation and the head of the fixture can be demaged!
Note:
If the feedback was switched off, the pan/tilt-position is changed by an external force and the feedback is switched
on again, the moving head might not to be synchronized with the DMX signal. You have to make a reset in order
to synchronize the moving head with the DMX signal.
Microphone Sensitivity
- Select this function to adjust the microphone sensitivity from 1(maximum) to 20 (minimum). If
the sensitivity is correctly adjusted, the mark will appear (blinking in the bass beat.)
Fan Modes - By using this function you can choose 2 types of the fan speed operating modes.
Auto Cooling - The fans automatically raise their speed in order to control inside temperature of the lighting,
if the temperature inside increases about certain level (the low fan speed reduces the cooling of the lighting).
This cycle can repeat several times until the temperature inside is on a suitable level.
High Cooling - The cooling fans work on max. speed (max. cooling). This mode we recommend for high ambient
temperature (0 °C and more).
Autofocus
- The function improves the image on the wall if the zoom changes (its effect is the best for gobos from gobo
wheel 2 and for distance cca m). If you want to focus the image on the long distance (more than 15 m), this
function should be set off.
Pan/Tilt mode
- Use this menu to set the character of the pan/tilt movement.
Time mode - Pan and tilt will move with different speeds and they will come at the same time to end point (pan
and tilt sets its optimal speed).
Speed Mode - Pan and tilt will move with the same speed as adjusted by the channel 5 (Pan/Tilt speed). E.g.
pan will come to the end point and wait for tilt, which has longer track.
Active Blackout while: - Use this function if you wish to close the light output during effect changes.
Pan/Tilt Moving - This function closes the light output during pan/tilt changes.
Colour Wheel Moving -
This function closes the light output during colour changes.
Gobo Wheels Moving -
This function closes the light output during gobo wheel 1/gobo wheel 2 changes.
IR Sensor - Select this function to switch on/off infra-red remote control .
Init Effect Positions
- Select this function to set all effects to the desired positions. After switching the fixture on (if DMX
is not connected), all effects will move to this init positions.
Note: If you operate 24 channels pre-setting (Mode 1) and you adjust DMX values for channels which are not
included in this mode, you will not be able to change these effects from the controller !
For example:
You operate the Mode 1 and in „Init Effect Positions” menu is adjusted
CMY Colour Macro =150,
this value
shoud be 0 or you will not abble to control cyan, magenta and yellow because these effects are used in CMY
macros and the macros have a priority.