RKI Instruments GasWatch 3 Скачать руководство пользователя страница 80

Страница: 80 / 95

80 • Appendix A: Maintenance Mode

GasWatch 3 for CO and O

Entering Maintenance Mode

WARNING:

The GasWatch 3 is not in operation as a gas detector while in Maintenance
Mode.

1. Take the GasWatch 3 to a non-hazardous location and turn it off if it is on.
2. Press and hold AIR, then press and hold POWER/MODE. You will hear a beep after one

second. Continue to hold the buttons down.

3. When you hear a second beep, release the buttons.

ID DISP (pg.86)

: User ID and Station ID screens appear in startup sequence. IDs can be changed in

Display Mode if

DISP.SET

in User Mode is also set to

OFF

(factory setting): User ID and Station ID screens do not appear in startup sequence.

IDs cannot be changed in Display Mode.

ZERO.SUP
(pg.86)

(factory setting): Not intended for field adjustment. The suppression value is 2 ppm.

ZERO.FLW
(pg.86)

(factory setting): Not intended for field adjustment.

ZSUP.DSP (pg.86)

: Zero suppression item appears in User Mode.

OFF

(factory setting): Zero suppression item does not appear in User Mode.

(Zero suppression item is always available in Maintenance Mode)

ZFLW.DSP
(pg.87)

: Zero follower item appears in User Mode.

OFF

(factory setting): Zero follower item does not appear in User Mode.

(Zero follower item is always available in Maintenance Mode)

CYL.DISP (pg.87)

(factory setting):

CYL SEL

item appears in

GAS CAL

OFF

CYL SEL

item does not appear in

GAS CAL

(RKI Instruments, Inc. does not recommend adjusting this setting.)

DATE (pg.87)

Set the current date and time.

PASS-W (pg.87)

(factory setting): Maintenance Mode is password-protected. Factory-set password is

3000

OFF

: Maintenance Mode is not password-protected.

ROM/SUM
(pg.88)

View the firmware information for the GasWatch 3’s sensor board and main board.

M.DEF (pg.89)

Set all parameters back to their RKI factory settings.

START (pg.90)

Press and release POWER/MODE to begin the warmup sequence and enter Measuring
Mode.

Table 11: Maintenance Mode Menu Items

Maintenance

Mode

Menu Item

Description

Содержание GasWatch 3
































































































Результаты поиска

Содержание GasWatch 3

Отзывы:

Похожие инструкции для GasWatch 3

Бренды по названию

Популярные бренды

RKI Instruments GasWatch 3, Руководство оператора

Результаты поиска

Содержание GasWatch 3

Отзывы:

Похожие инструкции для GasWatch 3

Бренды по названию

Популярные бренды