RKI Instruments GasWatch 3 Скачать руководство пользователя страница 88

Страница: 88 / 95

88 • Appendix A: Maintenance Mode

GasWatch 3 for CO and O

1. While in Maintenance Mode, press AIR to scroll to

PASS-W

2. Press and release POWER/MODE. The current setting flashes.
3. Use AIR to display the desired setting.
4. If you selected

OFF,

press and release POWER/MODE to save the setting and return to

the

PASS-W

item in User Mode.

If you selected

, continue with Step 5.

5. Press and release POWER/MODE. The Set Password Screen appears. The current

password displays and the first digit flashes.

6. Use AIR to display a number from 0 to 9.
7. Press and release POWER/MODE to enter the selection and advance to the next number.

To go back a number, press and hold AIR and POWER/MODE for a few seconds.

8. Repeat Step 6 and Step 7 to select the remaining numbers. When you press and release

POWER/MODE to enter the last number, the password is saved and the instrument returns

to the

PASSWORD

item in Maintenance Mode.

9. See “Entering Measuring Mode (START)” on page 90 to enter Measuring Mode.

Viewing the ROM/SUM (ROM/SUM)

The

ROM/SUM

screen shows the instrument’s firmware version and firmware checksum.

1. While in Maintenance Mode, press AIR to scroll to

ROM/SUM

PASS-W

3 0 0 0

ROM / SUM

Содержание GasWatch 3
































































































Результаты поиска

Содержание GasWatch 3

Отзывы:

Похожие инструкции для GasWatch 3

Бренды по названию

Популярные бренды

RKI Instruments GasWatch 3, Руководство оператора

Результаты поиска

Содержание GasWatch 3

Отзывы:

Похожие инструкции для GasWatch 3

Бренды по названию

Популярные бренды