RKI Instruments GasWatch 3 Скачать руководство пользователя страница 63

Страница: 63 / 95

GasWatch 3 for CO and O

Chapter 5: User Mode and Calibration • 63

1. After entering the

BUMP.SET

menu, press AIR to scroll to

BP.EXPD

2. Press and release POWER/MODE. The current setting flashes.
3. Use AIR to display the desired setting.
4. Press and release POWER/MODE to save the setting and return to the

BP.EXPD

item in

the

BUMP.SET

menu.

5. See “Exiting the BUMP.SET Menu” on page 63 to return to User Mode.

Exiting the BUMP.SET Menu

1. While in the

BUMP.SET

menu, press AIR to scroll to

ESCAPE

2. Press and release POWER/MODE to return to the

BUMP.SET

item in User Mode.

3. See “Entering Measuring Mode (START)” on page 72 to enter Measuring Mode.

Alarm Settings (ALARM--P)

The

ALARM--P

menu has 3 items:

ALARM--P

DEF.ALMP

, and

ESCAPE

1. While in User Mode, press AIR to scroll to

ALARM--P

2. Press and release POWER/MODE. The first screen displays.

BP .EXPD

ALARM--P

ppm

Содержание GasWatch 3
































































































Результаты поиска

Содержание GasWatch 3

Отзывы:

Похожие инструкции для GasWatch 3

Бренды по названию

Популярные бренды

RKI Instruments GasWatch 3, Руководство оператора

Результаты поиска

Содержание GasWatch 3

Отзывы:

Похожие инструкции для GasWatch 3

Бренды по названию

Популярные бренды