RKI Instruments GasWatch 3 Скачать руководство пользователя страница 20

Страница: 20 / 95

20 • Chapter 3: Measuring Mode

GasWatch 3 for CO and O

4. If a reading is observed, allow the reading to stabilize to determine the gas concentration

present.

5. If a gas alarm occurs, take appropriate action. See pg.22.

Alarms

This section covers alarm indications in Measuring Mode. It also describes how to reset the

GasWatch 3 after an alarm occurs and how to respond to an alarm condition.

NOTE:

False alarms may be caused by radio frequency (RF) or electromagnetic (EMI)

interference. Keep the GasWatch 3 away from RF and EMI sources such as radio

transmitters or large motors.

Alarm Indications

The GasWatch 3 buzzer sounds an alarm, the LEDs flash, and the vibrator pulses when any

sort of alarm condition or failure occurs. If the GasWatch 3 is operating in Stealth Mode, the

buzzer does not sound and the vibrator’s operation depends on the

VIB

setting in Gas Select

Mode’s

STEALTH

item. See pg.94 for more information.

NOTE:

If an alarm condition occurs while you are in Display Mode, the GasWatch 3

automatically returns to the Measuring Mode screen.

The table below summarizes the types of alarms produced by the GasWatch 3 and their

indications.

Table 4: Alarm Types and Indications

Alarm Type

Visual Indications

Other Indications

Warning

Concentration of gas rises above
the Warning setting for CO or falls
below the Warning setting for O

• Gas reading flashes
•

WARNING

appears at the bottom of

the LCD

• Alarm LEDs flash once per second
• Backlight turns on

• High-low tone sounds

once per second

• Vibrator pulses once per

second

Alarm

Concentration of gas rises above
the Alarm setting for CO or falls
below the Alarm setting for O

• Gas reading flashes
•

ALARM

appears at the bottom of the

LCD

• Alarm LEDs flash twice per second
• Backlight turns on

• High-low tone sounds

twice per second

• Vibrator pulses twice per

second

Alarm H

Concentration of gas rises above
the Alarm H setting.

• Gas reading flashes
•

ALARM H

appears at the bottom of

the LCD

• Alarm LEDs flash twice per second
• Backlight turns on

• High-low tone sounds

twice per second

• Vibrator pulses twice per

second

Содержание GasWatch 3
































































































Результаты поиска

Содержание GasWatch 3

Отзывы:

Похожие инструкции для GasWatch 3

Бренды по названию

Популярные бренды

RKI Instruments GasWatch 3, Руководство оператора

Результаты поиска

Содержание GasWatch 3

Отзывы:

Похожие инструкции для GasWatch 3

Бренды по названию

Популярные бренды