RKI Instruments GasWatch 3 Скачать руководство пользователя страница 53

Страница: 53 / 95

GasWatch 3 for CO and O

Chapter 5: User Mode and Calibration • 53

Option C from Flow Chart

Option D from Flow Chart

• Calibration passed
• One cylinder assigned
• Auto Start After Successful Cal set to

OFF (factory setting is ON)

• Calibration failed

1. The instrument indicates that all

channels passed the calibration.

2. The instrument shows the current gas

readings.

3. If

MAX.SPAN

is set to

(default is

OFF

, see pg.93), the response reading’s

maximum adjustment is displayed. A

maximum span of 100 ppm on the CO

channel indicates that the reading could

have been adjusted up to 100 ppm. If

the maximum span value is close to the

calibration gas value, the sensor should

be replaced soon.

The maximum CO adjustment is either

twice the calibration value or full scale,

whichever is lower. The maximum
oxygen adjustment is 25.0% volume.

4. Close the regulator.

5. Unscrew the regulator.

6. Remove the calibration cup.

7. The instrument continues to the

START

item in the

E-CAL

menu.

8. Press and release POWER/MODE to

enter Measuring Mode.

1. The instrument indicates which

channels failed the calibration.

2. Close the regulator.

3. Unscrew the regulator.

4. Remove the calibration cup.

5. Press and release POWER/MODE to

return to the E-CAL CYL X screen in

the

E-CAL

menu.

6. See “Troubleshooting” on page 73.

E-CAL

PASS

ppm

E-CAL

0.5

ppm

MAX.SPAN

24.0

ppm

E-CAL

FAIL

ppm

Содержание GasWatch 3
































































































Результаты поиска

Содержание GasWatch 3

Отзывы:

Похожие инструкции для GasWatch 3

Бренды по названию

Популярные бренды

RKI Instruments GasWatch 3, Руководство оператора

Результаты поиска

Содержание GasWatch 3

Отзывы:

Похожие инструкции для GasWatch 3

Бренды по названию

Популярные бренды