RKI Instruments GasWatch 3 Скачать руководство пользователя страница 93

Страница: 93 / 95

GasWatch 3 for CO and O

Appendix B: Gas Select Mode • 93

2. Press and release POWER/MODE. The display cycles through the following screens.

3. Press and release POWER/MODE to save the current alarm point settings as the default.
4. The instrument returns to the

SAVE-AP

item in Gas Select Mode.

5. See “Exiting Gas Select Mode (START)” on page 94 to enter Measuring Mode.

Turning Calibration Max Span On/Off (MAX.SPAN)

: After a passed calibration, the GasWatch 3 displays the response reading’s maximum

adjustment. A maximum span of 100 ppm on the CO channel indicates that the reading could

have been adjusted up to 100 ppm. If the maximum span value is close to the calibration

value, the sensor should be replaced soon. The upper limit on the maximum CO adjustment is

either twice the calibration value or full scale, whichever is lower. The upper limit on the

maximum oxygen adjustment is 25.0% volume.

OFF

(factory setting): There is no maximum span indication at the end of a calibration.

1. While in Gas Select Mode, press AIR to scroll to

MAX.SPAN

2. Press and release POWER/MODE. The current setting flashes.
3. Use AIR to display the desired setting.
4. Press and release POWER/MODE to save the setting and return to the

MAX.SPAN

item

in Gas Select Mode.

5. See “Exiting Gas Select Mode (START)” on page 94 to enter Measuring Mode.

SAVE-AP

SEL

YES .MODE

SEL

NO .AIR

SEL

MAX .SPAN

Содержание GasWatch 3
































































































Результаты поиска

Содержание GasWatch 3

Отзывы:

Похожие инструкции для GasWatch 3

Бренды по названию

Популярные бренды

RKI Instruments GasWatch 3, Руководство оператора

Результаты поиска

Содержание GasWatch 3

Отзывы:

Похожие инструкции для GasWatch 3

Бренды по названию

Популярные бренды