manualshive.com logo in svg

Rinnai ENERGYSAVER RHFE-308FTR, Руководство по установке, Страница: 6 / 32

Поделиться
Скачать
Rinnai ENERGYSAVER RHFE-308FTR Скачать руководство пользователя страница 6

Rinnai  6 ES_FIM

REGULATIONS & CLEARANCES

The heater and the flue system shall be installed in accordance with the following:

• 

Manufacturer’s Installation Instructions

• 

Current AS/NZS 3000, AS/NZS 3500 & AS 5601

• 

Local Regulations and Municipal Building Codes

• 

Any other relevant Statutory Regulation

IMPORTANT

Before commencing an installation, read the installation sections of the ‘Customer and Installation 

Manual’ supplied with the heater. Note that AS/NZS 5601 is referred to in this instruction and 

was current at the time of printing, but may have since been superseded. It is the Installer’s 

responsibility to ensure that requirements of the current version of AS/NZS 5601 are met.

These components 

MUST

 be installed, serviced and removed by an Authorised Person! 

ONLY

 the Rinnai flue 

system components specified in this manual 

MUST

 be used. Components 

NOT

 specified in this manual, whether 

manufactured by Rinnai or otherwise, are 

NOT

 compatible and 

MUST NOT 

be used!

Rinnai Energysaver space heater when correctly installed with Rinnai approved flue components are room-sealed 

appliances and no internal ventilation is required. The Rinnai Energysaver space heater is fan-assisted. Therefore 

the fan assisted flue clearance dimensions from AS/NZS 5601 extract shown on this page 

MUST

 be used.

The outer plastic section of the Co-Axial Flue complies with temperature hazard requirements and can be installed 

with zero clearance to combustible material. Vertical clearances when using a roof terminal (ESROOFCOWL) are 

shown in Fig.1. If in doubt contact the Rinnai Australia National Helpline (number on the back page).

Flue terminal

Fan assisted flue appliance only

Gas meter

Electricity meter or fuse box

Mechanical air inlet

Minimum Clearance 500 mm

ESROOFCOWL

Decktite or lead collar flashing

ESPLATE

ESPIPE900

Flue pipe clip supplied with ESPIPE900

Flue pipe clip supplied with ESROOFCOWL

Fan assisted

• 

Appliances

 up to 50 MJ/h input

200

• 

Appliances

 over 50 MJ/h input

300

b From the ground, above a balcony or other surface *

300

c Front a return wall or external corner *

300

d

From a gas 

meter

 (M) (see 5.11.5.9 for vent terminal location of 

regulator

)

(see Table 6.6 for New Zealand requirements)

1000

e From an electricity 

meter

 or fuse box (P) †

500

500

f From a drain pipe or soil pipe

75

g Horizontally from any building structure* = or obstruction facing a terminal
h From any other 

flue terminal

, cowl, or combustion air intake †

300

• 

Appliances

 up to 150 MJ/h input *

300

• 

Appliances

 over 150 MJ/h input up to 200 MJ/h input *

300

• 

Appliances

 over 200 MJ/h input up to 250 MJ/h input *

500

• 

Appliances

 over 250 MJ/h input  *

1500

• All fan-assisted 

flue appliances

, in the direction of discharge

1500

k From a mechanical air inlet, including a spa blower

1000

• Space heaters up to 50 MJ/h input

150

• Other 

appliances

 up to 50 MJ/h input

500

• 

Appliances

 over 50 MJ/h input and up to 150 MJ/h input

1000

• 

Appliances

 over 150 MJ/h input

1500

1

Where dimensions 

c, j

 or 

k

 cannot be achieved an equivalent horizontal distance 

measured diagonally from the nearest discharge point of the terminal to the opening 

may be deemed by the Technical Regulator to comply.

2

See Clause 6.9.4 for restrictions on a 

flue terminal 

under a covered area.

3

See Figure J3 for clearances required from a 

flue terminal 

to an LP Gas 

cylinder.

A 

flue terminal 

is considered to be a source of ignition.

4

Ref.

Item

a

Min. clearances (mm)

Below eaves, balconies and other projections:

j

Horizontally from an openable window, door, non-mechanical air inlet, or any other opening into a building 

with the exception of sub-floor ventilation:

Vertically below an openable window, non-mechanical air inlet, or any other opening into a building with the 

exception of sub-floor ventilation:

NOTES:

† - Prohibited area below electricity meter or fuse box extends to ground level.

FIGURE 6.2 (in-part) MINIMUM CLEARANCES REQUIRED FOR BALANCED FLUE TERMINALS, FAN-ASSISTED FLUE 

TERMINALS, ROOM-SEALED APPLIANCE TERMINALS AND OPENINGS OF OUTDOOR APPLIANCES

* - unless 

appliance

 is 

certified

 for closer installation

For 

appliance

s

not addressed above acceptance should be obtained from the Technical Regulator.

n

Horizontal Clearances (Extract AS/NZS 5601 Fig. 6.2)

NOTE

All Rinnai Energysaver space 

heaters are fan assisted (forced 

exhaust) appliances.

WARNINGS & IMPORTANT INFORMATION

Содержание ENERGYSAVER RHFE-308FTR

































Отзывы:

Нет отзывов