manualshive.com logo in svg

Rinnai ENERGYSAVER RHFE-308FTR, Руководство по установке, Страница: 5 / 32

Поделиться
Скачать
Rinnai ENERGYSAVER RHFE-308FTR Скачать руководство пользователя страница 5

Rinnai  5 ES_FIM

GRAPHICAL CONVENTIONS USED IN THIS MANUAL

The following symbols are used to highlight specific requirements during installation steps.

CLEARANCES

Where required clearances will be provided and 

MUST

 be observed.

FALL

Ensure that the specified 2° fall is maintained to either the terminal or condensate trap.

MEASURE

Required measurements will be provided and 

MUST

 be observed for correct installation.

CUT

Cut as required to the specified measurements.

FINISH

Ensure that burrs and swarf are removed from all cut ends.

DISCARD

Denotes items that are not required for the specific installation.

OBSERVE CORRECT ORIENTATION

Where specified ensure that components are installed with the correct vertical or horizontal orientation.

LUBRICATE

Use the supplied container of silicon grease to lubricate components. 

DO NOT

 use other lubricants as 

these may damage the flue components.

SECURE

Where specified secure components with either installer provided or component supplied fixings.

DO NOT

Failure to observe  

DO NOT

 instructions will void the warranty of an appliance and may cause injury 

or death.

!

CAUTION

Caution notes and or warnings that 

MUST

 be observed for safe and correct installations.

IMPORTANT

Important notes that 

MUST

 be observed for safe and correct installations.

NOTE

General hints and guides provided to ease the installation.

WARNINGS & IMPORTANT INFORMATION

Содержание ENERGYSAVER RHFE-308FTR

































Отзывы:

Нет отзывов