manualshive.com logo in svg

Rinnai ENERGYSAVER RHFE-308FTR, Руководство по установке, Страница: 13 / 32

Поделиться
Скачать
Rinnai ENERGYSAVER RHFE-308FTR Скачать руководство пользователя страница 13

Rinnai 13 ES_FIM

DIRECT FLUE INSTALLATION METHOD

C

D

F

G

E

Z

B

A

Activities for creating a Direct flue installation:

A

 Locate Heater.

B

 Create Wall Penetration.

C

 Connect Heater Exhaust. 

CAUTION

D

 Connect Combustion Air Hose. 

CAUTION

E

 Installation and fastening of Back Cover Kit. 

F

 Cut Components (as required). 

CAUTION

G

 Assemble Wall Terminal.

Z

 Finalise Installation & Commissioning of Heater.

The  Direct  flue  kit  (ESDFK)  is  suitable  for  walls  up  to  385mm  thick.  ESDFK  can  be  cut  to  length  to  suit  wall 

thickness’s less than 385mm thick. For wall thickness’s greater than 385mm Co-Axial Pipe(s) (ESPIPE900) can 

be fastened onto ESDFK to extend the flue length. Refer to the section "Direct Extended Flue Installation Method" 

on page 14 for details.

Steps for creating a Direct flue installation are as follows:

1. 

Create the wall penetration(s) in accordance with the section "Wall Penetrations" on page 10. 

 

 The minimum diameter required for wall the penetration for a DIRECT flue installation is 80mm to non 

combustible surfaces such as brick and 100mm to combustible surfaces such as plaster.

 Allow for a continuous 2° fall from the heater connection point to the wall terminal.

2.  Slide the internal wall plate over the terminal end of the ESDFK pipe until it is nested on the raised ring of the 

flue transition.

3. 

Pass the ESDFK through the internal wall penetration until the internal wall plate is flush with the wall.

4.  Create the wall terminal in accordance with "Component Assembly & Connection ~ ESROOFCOWL" on page 

23.

5.  Make the heater exhaust and combustion air hose connections in accordance with the section "Connecting 

Heater Exhaust" on page 28.

CAUTION

Air hose and heater exhaust connections at the Energysaver heater 

MUST

 be made and checked 

in accordance with these instructions. Improper connections may result in dangerous situations, 

for example, the dispersion of combustion products in the space being heated.

6. 

Install the correct back cover kit and fasten the heater and back cover kit to the internal wall surface. 

7. 

Commission the heater in accordance with the manufacturer instructions supplied with the heater.

2

Max’ wall thickness 385mm

Min’ required protrusion 15mm

Internal wall plate, outer face

1

3

Exter

ior wal

l

Interio

r wall

INSTALLATION METHODS

Содержание ENERGYSAVER RHFE-308FTR

































Отзывы:

Нет отзывов