Rinnai ENERGYSAVER RHFE-308FTR Скачать руководство пользователя страница 25

Страница: 25 / 32

Rinnai

ES_FIM

COMPONENT ASSEMBLY & CONNECTION "IN-WALL" FLUE ~ ESFKIT03 & ESKITIW

The In-Wall vertical Co-Axial flue system is installed within a stud wall with cavity depth a minimum of 90mm and

is run vertically upwards through the stud wall cavity and includes a condensate trap.
When considering the location of the heater due care

MUST

be taken to ensure that the flue path in the internal

wall and roof space are free of obstructions such as studs, noggins, joists, braces, and electricals etc. A top plate

bracket is provided to seal the flue penetration through the top plate.

Use the lower end points (

and

) of the flue spigot arc from "Wall Penetrations" on page 10 to determine

the shaded spigot area

Point

is the centre point of the transition casting and the point from which all measurements are taken. The

starting point

may be placed anywhere within the shaded spigot area

Using the dimensions shown above create a 300mm high by 200mm wide opening. The bottom left corner of

this opening is 75mm to the left of starting point

and 50mm below starting point

Remove the screw from the front of the transition casting (retain and

DO NOT

discard) and slide the wall

spacer plate over the transition casting so that the folded tab is facing both down and to the rear.
Using the screw removed from the front of the transition casting attach the mounting strip across the front of

the transition casting.

Lubricate the O-Ring of the condensate trap and attach this to the transition assembly

ensuring that

the drain tube is facing to the front.

Install the above assembly in to the wall cavity

observing the measurements shown to ensure the

correct fitting of heater and other components. Secure in place with appropriate fixings.

Outline of mounting strip

Outline of vermin plates

Required wall penetration

Bottom left corner of opening

300mm

200mm

75mm

50mm

(Appliance outline example RHFE-556)

iii

(Centre of flue elbow pivot point)

(Spigot area derived from

lower end points

and

)

(Minimum limit of arc)

Use in conjuction with section “WALL PENETRATIONS” on page 6.

Align this point within
the shaded area

Transition Casting/

Condensate Trap

Wall Spacer Plate

Mounting Strip

117

75mm

Condensate Drain

Tube Connection

Wall Spacer Plate

(Installed Position)

Pipe Locating Spacer

(See page 19 for deatails)

INSTALLATION METHODS

Содержание ENERGYSAVER RHFE-308FTR

































Результаты поиска

Содержание ENERGYSAVER RHFE-308FTR

Отзывы:

Rinnai ENERGYSAVER RHFE-308FTR, Руководство по установке, Страница: 25 / 32

Результаты поиска

Содержание ENERGYSAVER RHFE-308FTR

Отзывы: