Rinnai ENERGYSAVER RHFE-308FTR Скачать руководство пользователя страница 19

Страница: 19 / 32

Rinnai

ES_FIM

UNDER FLOOR FLUE INSTALLATION METHOD

Total flue length can be up

to nine (9) metres long and

can contain a maximum of

two (2) ESBEND (2x90°)!

Activities for creating a Sideways flue installation:

Modify ESDFK for Sideways Installation.

Create Penetration in floor

Locate Heater.

Connect Heater Exhaust.

CAUTION

Connect Combustion Air Hose.

CAUTION

Installation & fastening of Back Cover Kit (ESBSK)

Cut, Fit & Secure Components.

(seal joints as required)

CAUTION

Refer to steps

of Direct & Direct Extended.

(as required)

Finalise Installation & Commissioning of Heater.

The Down and Out flue option allows for a Direct Flue Kit (ESDFK) to face downwards and the flue to be run

vertically though a hole in the floor, and then horizontally to a suitable location outside.

CAUTION

Flue

MUST NOT

terminate under a building.

Flue terminal is

ONLY

available in the horizontal format.

Steps for creating a Under Floor flue installation are as follows:

Using a drill, remove the pop rivet used to fasten the straight flue pipe connection pipe to the flue transition of

ESDFK and remove but

DO NOT

discard the straight flue pipe connection.

2. Fit the elbowed flue pipe connection supplied with the Back Cover kit to the flue transition pushing it fully

home and then fasten in place with the grub screw (supplied) using an Allen key. The grub screw terminates in

a groove in the flue transition. When fastened this prevents accidental dislodgement of the pipe connections.

Refit the straight flue pipe connection to the end of the elbow until it is fully home and then fasten in place

with a 3mm rivet.

CAUTION

Ensure the straight pipe and elbow are securely fastened to the flue transition by the grub

screw and rivets.
Test soundness of the connections by attempting to 'pull apart' the assembled components.

Improper assembly or fastening can result in products of combustion dispersing into the room

being heated which may result in a dangerous condition.

4. Attach the side cover panels from the back cover kit (ESBSK A, B, C, D, E, F, G or H) to the rear of the heater

in accordance with the assembly Instructions supplied with the back cover kit and temporarily position the

heater in the desired position.
Check proposed route of down and out flue to confirm there are no obstructions in the flue path.

GRUB

SCREW

(Supplied)

3mm RIVET

INSTALLATION METHODS

Содержание ENERGYSAVER RHFE-308FTR

































Результаты поиска

Содержание ENERGYSAVER RHFE-308FTR

Отзывы:

Rinnai ENERGYSAVER RHFE-308FTR, Руководство по установке, Страница: 19 / 32

Результаты поиска

Содержание ENERGYSAVER RHFE-308FTR

Отзывы: