Rinnai ENERGYSAVER RHFE-308FTR Скачать руководство пользователя страница 24

Страница: 24 / 32

Rinnai

ES_FIM

COMPONENT ASSEMBLY & CONNECTION "ON-WALL" TERMINAL ~ ESWTKIT2

IMPORTANT

To terminate an ON-Wall terminal a connecting pipe is required, this component is created from

sections of ESPIPE900 outer and inner pipes which is then attached to ESBEND and or ESPIPE900

flue components. Use the diagram & table below when creating the connecting pipe sections.

Stopper dimple

Dimension

(mm)

Min. Dimension

(mm)

A + B + C

109

103

43 (B + E)

In accordance with the measurements provided above, measure

off and cut the outer pipe to required length

(minimum length is

70mm). Ensure that burrs and swarf are removed from all cut ends.

In accordance with the measurements provided above, measure

off and cut the inner pipe to required length

A + B + C

(minimum

length is 109mm). Ensure that burrs and swarf are removed from

all cut ends.

Lubricate the ‘O-Ring’ of the inner pipe of the preceding component,

this should be either an ESBEND or an ESPIPE900.

CAUTION

ONLY

use non-acidic silicone sealant between the joints

of PVC flue pipe and any mating aluminium components

(such as those of ESROOFCOWL) to secure and seal these

joints against ingress of dust and water.
Silicone containing acetic acid, (characteristically having a

vinegar odour), as the curing agent or other acids may cause

corrosion of aluminium components and

MUST NOT

used.

Insert the cut section of inner pipe into the female socket of the

preceding component, ensuring that it is fully home. Then insert the cut

section of outer pipe into the female socket of the preceding component,

ensuring it is also fully home. There should

ONLY

be 27mm of inner

pipe section protruding when both inner and outer are fitted correctly.

IMPORTANT

When preparing an on wall terminal ensure a continuous

2° fall from the flue termination point back towards the

heater (condensate trap). This is especially important when

an ESPIPE900 is used to horizontally extend the terminal

location for the clearance considerations.
Additional supports may also be required.

Attach the flue terminal to the flue adapter using the three m4

screws supplied.

With the orientation arrow is pointing vertically upwards,

attach the above terminal assembly to the connecting pipes, ensuring

that the outer pipe hits the stopper dimples of the flue adapter. Then

secure the terminal in place with the two 8g screws supplied.

CAUTION

For the on wall terminal it is

CRITICAL

that the joints of PVC

outer pipes are sealed with an appropriate PVC solvent.

A (70mm min)

A + B + C (109mm min)

C (27mm)

Extended

horizontal

C (27mm)

Direct

horizontal

INSTALLATION METHODS

Содержание ENERGYSAVER RHFE-308FTR

































Результаты поиска

Содержание ENERGYSAVER RHFE-308FTR

Отзывы:

Rinnai ENERGYSAVER RHFE-308FTR, Руководство по установке, Страница: 24 / 32

Результаты поиска

Содержание ENERGYSAVER RHFE-308FTR

Отзывы: