Riello RLS 310/E MX, Инструкции по установке, использованию и обслуживанию

Страница: 69 / 96

67
20081825
GB
Faults - Possible causes - Solutions
127 # EEPROM access internal error
Carry out a reset, repeat and check the last setting of the
parameters. Restore the group of parameters: if the error arises
repeatedly, replace the control box.
128 0
EEPROM access internal error - synchronisation
during the initialisation Carry out a reset; If the error arises repeatedly, replace the
control box.
129 #
EEPROM access internal error – command
synchronisation
Carry out a reset, repeat and check the last setting of the
parameters. If the error arises repeatedly, replace the control
box.
130 # EEPROM access internal error - time-out
Carry out a reset, repeat and check the last setting of the
parameters. If the error arises repeatedly, replace the control
box.
131 # EEPROM access internal error - page interrupted
Carry out a reset, repeat and check the last setting of the
parameters. If the error arises repeatedly, replace the control
box.
132 # EEPROM register initialisation internal error
Carry out a reset; if the error arises repeatedly, replace the
control box.
133 ÷ 135 #
EEPROM access internal error – request
synchronisation
Carry out a reset, repeat and check the last setting of the
parameters. If the error arises repeatedly, replace the control
box.
136 1 Restoration started The restoration of a backup has been started (no error)
137 # Internal error – backup / restoration
157 (-99)
Restoration – OK, but backup < compared with set data of
current system Restoration successful, but the backup data installed are fewer
than those currently present in the system.
239 (-17) Backup - logging of the backup on RDI21… failed Perform the reset and repeat backup
240 (-16) Reset - no backup in RDI21… No backup in RDI21…
241 (-15) Reset - Interruptions relating to impracticable ASN
The backup has an impracticable ASN and cannot reset the
unit
242 (-14) Backup – the backup carried out is contradictory The backup is irregular and cannot be transferred again
243 (-13)
Backup – the data comparison between the internal
microprocessors is irregular
Repeat the reset and backup
244 (-12) The backup data are incompatible
The backup data are incompatible with the current version of
the software; the restoration is not possible
245 (-11) Error in access to the parameter Restore_Complete Repeat the reset and backup
246 (-10) Restoration – time-out during logging in EEPROM Repeat the reset and backup
247 (-9) The data received are contradictory
The series of backup data is not valid; restoration is not
possible
248 (-8) The restoration cannot currently be carried out Repeat the reset and backup
249 (-7)
Restoration – interruption caused by inadequate
identification of the burner The backup has an inadequate identification of the burner and
must not be transferred to the control box
250 (-6) Backup – the CRC of a page is not correct
The series of backup data is not valid; restoration is not
possible
251 (-5) Backup – the identification of the burner is not defined Define the identification of the burner and repeat the backup
252 (-4) After restoration, the pages are still in INTERRUPTION Repeat the reset and backup
253 (-3) The restoration cannot currently be carried out Repeat the reset and backup
254 (-2) Interruption owing to transmission error Repeat the reset and backup
255 (-1) Interruption owing to time-out during the restoration Carry out a reset, check the connections and repeat the backup
146 # Time-out of the system automation interface Refer to the Modbus User Documentation (A7541)
1 Modbus time-out
150 # TÜV test
1 (-1) Invalid phase The TÜV test can only be started in phase 60 (operation)
2 (-2) The TÜV test default output is too low
The output of the TÜV test must be lower than the minor output
limit
3 (-3) The TÜV test default output is too high
The output of the TÜV test must be greater than the upper
output limit
4 (-4) Manual interruption No error: Manual interruption of the TÜV test by the user
5 (-5) TÜV test time-out
No flame loss after the fuel valves have been closed
1. Check for any extraneous lights
2. Check that there are no short-circuits
3. Check whether one of the valves is leaking
165 # Internal error
166 0 Watchdog reset internal error
Error
code
Diagnostic code Meaning of the LMV 26... system Recommended measures