Ricon SLIDE-AWAY ST00 Скачать руководство пользователя страница 21

Страница: 21 / 71

S-SERIES PRIVATE USE SERVICE MANUAL

INSTALLATION

SEPTEMBER 2020

2 - 10

32DSW02.F

TABLE 2-3: LIMIT SWITCH ADJUSTMENT CHART

COMPONENT

SYMPTOM

CORRECTIVE

ACTION

ADJUSTMENT PROCEDURE

Fold cutoff

actuator

Lift does not

fold tightly.

Rotate actuator

counter-

clockwise.

With lift fully folded (handrails should be

folded tight against vertical arms), rotate

actuator so that it barely trips fold cutoff

switch.

Pump runs

continuously.

Rotate actuator

clockwise.

Test lift. Pump should cutoff when lift is

folded tight.

Up cutoff

adjustment

screw

Lift stops

low.

Adjust screw

clockwise.

Adjust up cutoff switch so that lift stops just

before first knuckle actuator saddle or roller

touches underside of lower parallel arm.

(Saddle or roller should be about 1/8" from

lower parallel arm.)

Lift stops

high.

Adjust screw

counter-

clockwise.

Deploy cutoff

adjustment

screw

Lift stops

low.

Adjust screw

counter-

clockwise.

Adjust deploy limit switch so that lift stops

just below "Up" cutoff described in above

step. This will give the necessary overlap

to avoid "dead" spots.

Lift stops

high.

Adjust screw

clockwise.

END OF TABLE

PLATFORM TILT ADJUSTMENT

Correct platform tilt adjustment is crucial for proper platform rollstop operation, but cannot be adjusted at factory.

Factors such as vehicle floor height, lift tilt angle and stiffness of vehicle springs will vary installation geometry.

a. Deploy and lower lift platform to ground level.
b. Refer to

Figure 2-11

. Adjust left and right platform set screws until platform is level at zero degrees.

Turn setscrews clockwise to angle front-end of platform upward, or counter-clockwise to angle downward.

NOTE:

At ground level, the distance between heel of platform and ground should be 3/4" to 1". This distance

should be measured at initial point of rollstop full deployment.

NOTE:

Adjust setscrews on both sides of platform simultaneously and evenly to ensure proper leveling of plat-

form.

c. Repeat steps a and b as required to achieve proper rollstop operation.

SET SCREW

PLATFORM

FIGURE 2-11: PLATFORM SET SCREWS

Содержание SLIDE-AWAY ST00








































































Результаты поиска

Содержание SLIDE-AWAY ST00

Отзывы:

Похожие инструкции для SLIDE-AWAY ST00

Бренды по названию

Популярные бренды

Ricon SLIDE-AWAY ST00, Руководство по обслуживанию

Результаты поиска

Содержание SLIDE-AWAY ST00

Отзывы:

Похожие инструкции для SLIDE-AWAY ST00

Бренды по названию

Популярные бренды