Ricon SLIDE-AWAY ST00 Скачать руководство пользователя страница 19

Страница: 19 / 71

S-SERIES PRIVATE USE SERVICE MANUAL

INSTALLATION

SEPTEMBER 2020

2 - 8

32DSW02.F

INTERLOCK DEVICE INSTALLATION

The supplied interlock device must be installed to prevent operation of the lift or vehicle when it is unsafe to do so.
The Slide-Away lift provides an electrical interlock signal to the vehicle that prevents movement of the vehicle un-

less the platform is fully stowed. The interlock control also supplies power to the lift only when the vehicle parking

brake is set and the transmission is in PARK.

NOTE:

An 8-amp circuit breaker is located within the lift as a circuit protection device. The circuit interface used

by the installer must be capable of carrying an additional 8 amps of continuous current.

Refer to

Figure 2-8

. The interlock installation kit provides a display panel for mounting on the vehicle dashboard.

The figure shows an LED display panel. The Lift Power LED lights green when the vehicle transmission is in

PARK and the parking brake is set. While the LED is green the lift is lowered and the platform can be deployed.

The Not Stowed LED lights red when the platform is not fully stowed into the vehicle. While the LED is red the

transmission cannot be shifted out of PARK.

NOT STOWED

LIFT POWER

(GREEN)

(RED)

FIGURE 2-8: INSTERLOCK DISPLAY PANEL

The installer must verify that none of the original equipment circuit breakers, fuses, or solenoids are bypassed,

removed, or altered. Be sure that no wires are left frayed or hanging loose after installation of the interlock de-

vice. If you have any questions concerning the proper installation of this interlock device, please contact our

Product Support department.

C. FINAL ADJUSTMENTS

LIMIT SWITCH ADJUSTMENT

Refer to

Figures 2-9, 2-10,

and the following procedure.

NOTE:

To avoid operational “dead-spots”, adjust DEPLOY CUTOFF SWITCH before UP CUTOFF SWITCH.

NOTE:

When loosening adjustment screws, apply enough pressure to screw to move block instead of screw.

(The block might stick if insufficient pressure is applied to screw.)

FIGURE 2-9: LIMIT SWITCH ADJUSTMENT DIAGRAM

SWITCH

DEPLOY CUTOFF

ADJUSTMENT

FOLD CUTOFF

UP CUTOFF

SCREW

DEPLOY CUTOFF

LOWER

UP CUTOFF SWITCH

ACTUATOR

CAM

FOLD CUTOFF

ADJUSTMENT

SCREW

CAM LOBE

SWITCH

Содержание SLIDE-AWAY ST00








































































Результаты поиска

Содержание SLIDE-AWAY ST00

Отзывы:

Похожие инструкции для SLIDE-AWAY ST00

Бренды по названию

Популярные бренды

Ricon SLIDE-AWAY ST00, Руководство по обслуживанию

Результаты поиска

Содержание SLIDE-AWAY ST00

Отзывы:

Похожие инструкции для SLIDE-AWAY ST00

Бренды по названию

Популярные бренды