background image

MAINTENANCE

 

S-SERIES PRIVATE USE SERVICE  MANUAL 

 

SEPTEMBER 2020 

3- 10 

                                                                                             32DSW02.F

   

 

 

 

 

 

 

 

   

 

 

FIGURE 3-17

 

 

 

 

 

 

FIGURE 3-18

 

3.  Refer to

 Figure 3-19

.  Slide gas spring inward then lift and remove from baseplate. 

 

FIGURE 3-19

 

4.  Remove the screw and collar that attaches the cable to baseplate and retain for installation. 
5.  Remove cable from baseplate.  Discard old cable. 

NOTE: 

Do not reuse old cable.  Use Cable (P/N 35233) provided in Kit (P/N 36998). 

6.  Install cable (P/N 35233) and secure with existing screw and collar, retained from step12, Section E. 

NOTE: 

Do not reuse old cable.  Use Cable (P/N 35233) provided in Kit (P/N 36998). 

7.  Refer to

 Figure 3-20

.  Install clevis (P/N 35232) onto gas spring (P/N 39368). 

RSB0000500

GAS SP R ING (P /N 39368 )

LOCK NU T (P /N 14-08 -304 )

P ULLEY SHIELD (P/N 35958 )

CLEVIS (P/N 35232 )

G ROO VE D BEA RIN G (P/N VS -AH -06 )

1/4-20 X 7/8" SC REW (P /N 39 370 )

THREADED END

 

FIGURE 3-20

 

8.  Refer to

 Figure 3-20

.  Assemble grooved bearing (P/N VS-AH-06), pulley shield (P/N 35958) and 

attaching parts onto clevis (P/N 35232).  Do not tighten. 

NOTE: 

Do not tighten ¼-20 screw onto pulley shield with lock nut until cable has been routed onto grooved 

bearing. 

Содержание SLIDE-AWAY ST00








































































Отзывы: