Ricoh Kr-P2 Скачать руководство пользователя страница 154 | Manualshive

Страница: 154 / 200

background image

5816 201

Instl: Condition

Displays a number that indicates the status of the @Remote service device.
0: Neither the registered device by the embedded RCG nor embedded RCG device is
set.
1: The embedded RCG device is being set. Only Box registration is completed. In this
status the external RCG unit cannot answer a polling request.
2: The embedded RCG device is set. In this status the external RCG unit cannot answer
a polling request.
3: The registered device by the embedded RCG is being set. In this status the embedded
RCG device cannot be set.
4: The registered module by the embedded RCG has not started.

5816 202

Instl: ID #

Allows entry of the number of the request needed for the
embedded RCG device.

5816 203

Instl: Reference

Executes the inquiry request to the @Remote GateWay
URL.

5816 204

Instl Ref Result

Displays a number that indicates the result of the inquiry executed with SP5816 203.
0: Succeeded
1: Inquiry number error
2: Registration in progress
3: Proxy error (proxy enabled)
4: Proxy error (proxy disabled)
5: Proxy error (Illegal user name or password)
6: Communication error
7: Certification update error
8: Other error
9: Inquiry executing

5816 205

Instl: Ref Section

Displays the result of the notification sent to the device from the GW URL in answer to the
inquiry request. Displayed only when the result is registered at the GW URL.

5816 206

Instl: Rgstltn

Executes Embedded RCG Registration.

3. Appendix: SP Mode Tables

56

3

«
...
152
153
154
155
156
...
»

Содержание Kr-P2









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Kr-P2

Sure shot 80 tele

Бренд: Canon Страницы: 24

iPF720 - imagePROGRAF Color Inkjet Printer

Бренд: Canon Страницы: 8

Бренд: Canon Страницы: 2

Бренд: Xerox Страницы: 93

Бренд: Xerox Страницы: 36

Copycentre C118

Бренд: Xerox Страницы: 12

7400DN - Phaser Color LED Printer

Бренд: Xerox Страницы: 3

Бренд: Xerox Страницы: 136

4250 - WorkCentre - Copier

Бренд: Xerox Страницы: 4

4250 - WorkCentre - Copier

Бренд: Xerox Страницы: 4

Бренд: Xerox Страницы: 8

4150 - WorkCentre B/W Laser

Бренд: Xerox Страницы: 4

4150 - WorkCentre B/W Laser

Бренд: Xerox Страницы: 40

4150 - WorkCentre B/W Laser

Бренд: Xerox Страницы: 38

4150 - WorkCentre B/W Laser

Бренд: Xerox Страницы: 201

4150 - WorkCentre B/W Laser

Бренд: Xerox Страницы: 24

4118P - WorkCentre B/W Laser

Бренд: Xerox Страницы: 2

3635MFP - Phaser B/W Laser

Бренд: Xerox Страницы: 212

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды