Ricoh Kr-P2 Скачать руководство пользователя страница 132

Страница: 132 / 200

3923

WasteTonerLimiter

[0 or 1 / 1 /-]

Turns on or off the waste toner limiter. The waste toner limiter is executed by the threshold
time of the PCU rotation.
0: No (Off), 1: Yes (On)

3924

Toner End Sensor

3924 1

Toner Near-end

[100 to 1000 / 200 / 100 ms step] DFU

Threshold adjustment for toner near-end detection.

3924 2

Toner End

[250 to 1050 / 550 / 50 ms step] DFU

Threshold adjustment for toner end detection

3927

Toner End Judge

This SP code determines whether the machine disables printing when the machine detects
toner end.

• Even when toner end is detected, there is a small amount of toner left in the AIO. If

a user wants to print with the AIO until all toner is used up, then set this SP to 1. But
then, there is no toner end detection, and the user must watch the print quality and
change the AIO when prints become too pale.

[0 or 1 / 0 / -]
0: Yes (Printing stops when toner end is detected.)
1: No (Printing can continue even after toner end is detected.)

SP5-xxx: Mode

5001

All Indicators On

Turns on or off the all indicators on the operation panel.

5024

mm/inch Selection

0: Europe/Asia (mm), 1: North America (inch)

Selects the unit of measurement.
After selection, turn the main power switch off and on.

3. Appendix: SP Mode Tables

Содержание Kr-P2









































































































































































































Результаты поиска

Содержание Kr-P2

Отзывы:

Похожие инструкции для Kr-P2

Бренды по названию

Популярные бренды

Ricoh Kr-P2, Руководство по обслуживанию на месте

Результаты поиска

Содержание Kr-P2

Отзывы:

Похожие инструкции для Kr-P2

Бренды по названию

Популярные бренды