Ricoh Kr-P2 Скачать руководство пользователя страница 127

Страница: 127 / 200

1003 1 BypassTray Plain

[–8 to 8 / 0 / 1 mm step]

1003 2 BypassTray Thick

1003 3 BypassTray Thick2

1003 4 MainTray Plain

1003 5 MainTray Thick

1003 6 MainTray Thick2

1003 7 BankTray Plain

1003 8 BankTray Thick

1003 9 BankTray Thick2

1003 10 Duplex

1104

Fusing control

0: Normal, 1: Phase control

Use phase control if the room lights flicker when the fusing lamp starts.
Defaults: North America – Normal (On/off control), Europe – Phase

1105

Fusing Temp.

Adjusts the fusing temperatures for printing and standby mode.

1105 1

Plain

[150 to 200 / 170 / 5 deg.] DFU

Adjusts the fusing temperature for printing on normal paper.

1105 2

Thick2

[150 to 195 / 185 / 5 deg.] DFU

Adjusts the fusing temperature for printing on thick 2 paper.

1105 3

Standby Temp

[140 to 175 / 168 / 1 deg.] DFU

Adjusts the fusing temperature for standby mode.

1106

Fusing Temp Disp

1106 1 Displays the current fusing temperature.

SP Tables

Содержание Kr-P2









































































































































































































Результаты поиска

Содержание Kr-P2

Отзывы:

Похожие инструкции для Kr-P2

Бренды по названию

Популярные бренды

Ricoh Kr-P2, Руководство по обслуживанию на месте

Результаты поиска

Содержание Kr-P2

Отзывы:

Похожие инструкции для Kr-P2

Бренды по названию

Популярные бренды