Ricoh Kr-P2 Скачать руководство пользователя страница 153 | Manualshive

Страница: 153 / 200

background image

5816 085

Firm UpUsr Conf

This SP setting determines if the operator can confirm the
previous version of the firmware before the firmware
update execution. If the option to confirm the previous
version is selected, a notification is sent to the system
manager and the firmware update is done with the
firmware files from the URL.

5816 086

Firmware Size

Allows the service technician to confirm the size of the
firmware data files during the firmware update
execution.

5816 087

CERT: MacroVsn

Displays the macro version of the @Remote certification.

5816 088

CERT: PAC Vsn

Displays the PAC version of the @Remote certification.

5816 089

CERT: ID2 Code

Displays ID2 for the @Remote certification. Spaces are
displayed as underscores (_). Asteriskes (***) indicate
that no @Remote certification exists.

5816 090

CERT: Subject

Displays the common name of the @Remote certification
subject. CN = the following 17 bytes. Spaces are
displayed as underscores (_). Asterisks (***) indicate
that no DESS exists.

5816 091

CERT: SeriNum

Displays serial number for the @Remote certification.
Asterisks (***) indicate that no DESS exists.

5816 092

CERT: Issuer

Displays the common name of the issuer of the @Remote
certification. CN = the following 30 bytes. Asteriskes
(***) indicate that no DESS exists.

5816 093

CERT: St ExpTime

Displays the start time of the period for which the current
@Remote certification is enabled.

5816 094

CERT: Valid End

Displays the end time of the period for which the current
@Remote certification is enabled.

5816 200

Polling Man Exc

Executes manual polling. Cumin periodically polls the @Remote Gateway by HTTPS. This
is called "center polling". Use this SP at any time to poll the @Remote supply center.

SP Tables

55

3

«
...
151
152
153
154
155
...
»

Содержание Kr-P2









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Kr-P2

Бренд: Zeka Страницы: 54

Бренд: Xerox Страницы: 34

Бренд: Canon Страницы: 12

imagePROGRAF iPF8300S

Бренд: Canon Страницы: 52

Бренд: Canon Страницы: 2

Бренд: Panasonic Страницы: 9

Бренд: Panasonic Страницы: 2

Бренд: Datecs Страницы: 73

Бренд: Datamax Страницы: 12

E-Class Mark II

Бренд: Datamax Страницы: 40

Бренд: Datamax Страницы: 46

Бренд: Nantian Electronics Страницы: 4

Бренд: QMS Страницы: 208

Бренд: IBM Страницы: 60

Бренд: Canon Страницы: 20

PIXMA TS9100 Series

Бренд: Canon Страницы: 100

Бренд: Canon Страницы: 100

Бренд: Canon Страницы: 105

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды