Ricoh Kr-P2 Скачать руководство пользователя страница 134 | Manualshive

Страница: 134 / 200

background image

5302

Set Time

002

Time Difference

Sets the time clock for the local time. This setting is done at the factory before delivery.
The setting is GMT expressed in minutes.
[–1440 to 1440 / - / 1 min.]
Japan: +540 (Tokyo)
NA: -300 (NY)
EU: +60 (Paris)
CH: +480 (Peking)
TW: +480 (Taipei)
AS: +480 (Hong Kong)
KO: +540 (Korea)

5307

Summer Time

Lets you set the machine to adjust its date and time automatically with the change to
Daylight Savings time in the spring and back to normal time in the fall. This SP lets you set
these items:
Day and time to go forward automatically in April.
Day and time to go back automatically in October.
Set the length of time to go forward and back automatically.
The settings for 002 and 003 are done with 8-digit numbers:

3. Appendix: SP Mode Tables

36

3

«
...
132
133
134
135
136
...
»

Содержание Kr-P2









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Kr-P2

Бренд: 3Doodler Страницы: 8

Бренд: Zmorph Страницы: 16

7400DT - Phaser Color LED Printer

Бренд: Xerox Страницы: 20

Бренд: idp Страницы: 104

Бренд: Konica Minolta Страницы: 266

Бренд: Xiamen Hanin Electronic Technology Страницы: 62

Бренд: Axis Страницы: 10

Бренд: Citizen Страницы: 4

7400DN - Phaser Color LED Printer

Бренд: Xerox Страницы: 3

Бренд: SPRT Страницы: 18

Бренд: HandTop Страницы: 97

Бренд: Epson Stylus Страницы: 2

Бренд: UP Страницы: 37

Бренд: Xerox Страницы: 4

Бренд: Epson Страницы: 16

Бренд: Epson Страницы: 2

CX3810 - Stylus Color Inkjet

Бренд: Epson Страницы: 36

CX3810 - Stylus Color Inkjet

Бренд: Epson Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды