Ricoh Kr-P2 Скачать руководство пользователя страница 112

Страница: 112 / 200

Code No.

Symptom

Possible Cause

543

Fusing overheat error: Software

• Fusing thermistor defective
• Power supply board defective

A fusing temperature of over 235

C is

detected for 0.5 seconds by the fusing
thermistor.

544

Fusing overheat error: Software

• Fusing control out of control
• Power supply board defective

The machine detects an overheat error of
the hardware.

545

Fusing lamp stays on

• Fusing thermistor defective
• Power supply board defective
• Defective connection of the fusing unit

The fusing lamp stays on more than 12
seconds after the main motor has been
turned off.

547

Zero cross signal malfunction

• Power supply board defective
• Unstable main power supply

condition

Zero cross signals are already detected for
0.15 seconds before the fusing relay-on.

Zero cross signals are not detected for 3
seconds or the machine cannot detect a
frequency.

559

Fusing jam error: 3 counts

• Obstacle in the paper transport path
• Fusing unit installed incorrectly
• Fusing unit defective

At the fusing exit sensor the paper jam is
detected late for three pulse counts (lag
error) when SP1913-001 is set to "1: Yes".

620

Communication error - GAVD

• Engine board defective

The engine board detects an unknown
device.

622

Communication error - PFU

• Noise
• Harness connection disconnected

between the machine and PFU

Three consecutive errors are detected
during polling after the PFU is successfully
detected by the machine.

2. Appendix: Troubleshooting Guide

Содержание Kr-P2









































































































































































































Результаты поиска

Содержание Kr-P2

Отзывы:

Похожие инструкции для Kr-P2

Бренды по названию

Популярные бренды

Ricoh Kr-P2, Руководство по обслуживанию на месте

Результаты поиска

Содержание Kr-P2

Отзывы:

Похожие инструкции для Kr-P2

Бренды по названию

Популярные бренды