Ricoh Aficio SP 5100N Скачать руководство пользователя страница 155

Страница: 155 / 175

Engine Hardware Specifications

SM 6-17

G186

Det

ailed

Section

Des

cription

Error

Description

LCD Display

OPEN HEAT

ERROR

When warming up, it has been lower

than 60°C over 35 seconds.

"ENGINE FUSER

ERROR"

LOW HEAT

ERROR

Standby - It has been lower than 130°C

over 10 seconds.

Printing

Up to 2 consecutive pages :

It has been lower than 155°C over 7

seconds.

From 3 consecutive pages :

It has been 25°C lower than the fixed

fusing temperature over 7 seconds.

"ENGINE LOW

HEAT ERROR"

OVER HEAT

ERROR

It has been higher than 230°C over 10

seconds.

"ENGINE

OVERHEAT

ERROR"

This can be changed in the future.

LSU

The LSU consists of the LD (Laser Diode) and the polygon motor control. When the printing

signal occurs, it turns on the LD and drives the polygon motor. When the detector detects

the beam, Hsync occurs. Error messages are as follows:

Error

Description

LCD Display

Polygon Motor

Error

When the polygon motor speed does not

become steady.

"LSU NOT READY"

LOW HEAT

ERROR

The polygon motor speed is steady but

Hsync is not generated.

"HSYNC ERROR"

Содержание Aficio SP 5100N
















































































































































































Результаты поиска

Содержание Aficio SP 5100N

Отзывы:

Похожие инструкции для Aficio SP 5100N

Бренды по названию

Популярные бренды

Ricoh Aficio SP 5100N, Руководство по обслуживанию

Результаты поиска

Содержание Aficio SP 5100N

Отзывы:

Похожие инструкции для Aficio SP 5100N

Бренды по названию

Популярные бренды