Ricoh Aficio SP 5100N Скачать руководство пользователя страница 129

Страница: 129 / 175

EDC (Engine Diagnostic Control) Mode

SM 5-11

G186

Service

bles

Function Name

Description

Display (LCD)

Remarks

THV Minus Bias

The bias will have the

previously saved value.

THV Minus Bias

[ON] / [OFF]

DEV Bias

The bias will have the

previously saved value.

DEV Bias [ON] /

[OFF]

DEV AC Bias

The bias will have the

previously saved value.

DEV AC Bias

[ON] / [OFF]

DEV Vpp Bias

The bias will have the

previously saved value.

DEV Vpp Bias

[ON] / [OFF]

MHV Bias

The bias will have the

previously saved value.

MHV Bias

[ON] / [OFF]

PTL

The lamp will be lighted or

not.

PTL [ON] / [OFF]

Erase Lamp

The lamp will be lighted or

not.

Erase Lamp

[ON] / [OFF]

TR Cur

The Adc will be displayed

on the panel.

TR Cur [xxx]

[xxx] is it’s ADC.

CR Cur

The Adc will be displayed

on the panel.

CR Cur [xxx]

[xxx] is it’s ADC.

The procedure and content above may vary, depending on the situation.

5.2.11 CRU COUNTER

This function is used to check the counters.

Usage

6. Press the arrow keys "

(

" until "Component Test / 8. CPU Counters" message is

displayed.

7. Press the "OK" key.

8. Press the arrow keys "

(

" to find the desired function (Refer to the table below).

9. Press the "OK" key.

Содержание Aficio SP 5100N
















































































































































































Результаты поиска

Содержание Aficio SP 5100N

Отзывы:

Похожие инструкции для Aficio SP 5100N

Бренды по названию

Популярные бренды

Ricoh Aficio SP 5100N, Руководство по обслуживанию

Результаты поиска

Содержание Aficio SP 5100N

Отзывы:

Похожие инструкции для Aficio SP 5100N

Бренды по названию

Популярные бренды