Ricoh Aficio SP 5100N Скачать руководство пользователя страница 107

Страница: 107 / 175

Malfunction Causes and Solutions

SM 4-21

G186

ouble

shooting

4.4 MALFUNCTION CAUSES AND SOLUTIONS

4.4.1 FUSER ERROR

Description:

A message “Engine Fuser Low Heat Error/Engine Fuser Over Heat Error” is displayed in

the LCD panel.

Check for...

Solutions

1. Check whether thermostat is open or

not.

2. Check whether thermistor is open or

not.

3. Heat lamp ON/OFF test

4. Operation is impossible due to a gear

of a fuser being melted.

1. Replace the fuser if the thermostat is

open.

2. Replace the fuser if a thermistor sensor

is located deep inside of a sponge.

3. Check whether the overheat mode

circuit is operating normally or not.

4. Replace

the

fuser.

4.4.2 LSU (LASER SCANNING UNIT) ERROR

Description:

A message “Engine Hsyne Error” is displayed in the LCD panel.

Check for...

Solutions

1. Check whether the LSU (Laser

Scanning Unit) connector is

disconnected or not.

2. Check whether the LSU motor is

rotating or not.

3. Check the HSYNC signal.

1. Connect the LSU harness properly.

2. Replace

the

LSU.

3. Replace the main board if the same

error occurs again after replacing the

LSU.

Содержание Aficio SP 5100N
















































































































































































Результаты поиска

Содержание Aficio SP 5100N

Отзывы:

Похожие инструкции для Aficio SP 5100N

Бренды по названию

Популярные бренды

Ricoh Aficio SP 5100N, Руководство по обслуживанию

Результаты поиска

Содержание Aficio SP 5100N

Отзывы:

Похожие инструкции для Aficio SP 5100N

Бренды по названию

Популярные бренды