Ricoh Aficio SP 5100N Скачать руководство пользователя страница 125

Страница: 125 / 175

EDC (Engine Diagnostic Control) Mode

SM 5-7

G186

Service

bles

Function Name

Description

Display (LCD)

T4 Feed Motor

The tray2 motor will run in the forward

direction or stop.

T Feed Motor [ON] / [OFF]

The procedure and content above may vary, depending on the situation.

5.2.6 FAN TEST

These functions are to check the current status of all fans.

Usage

1. Press the arrow keys "

(

" until "Component Test / 3.Fan Test" message is displayed

on the panel.

2. Press the "OK" key.

3. Press the arrow keys "

(

" to find a desired function (Refer to the table below).

4. Press the "OK" key.

5. Press the "OK" key to execute the function or the "Back" to return to the previous step.

Function

Function Name

Description

Display (LCD)

Fuser Fan

The fan will run or stop.

Fuser Fan [ON] / [OFF]

Fuser Fan Rdy

Check whether the fan is in locked

state.

Fuser Fan Rdy.

[Ready] / [Not Ready]

SMPS Fan

The fan will run or stop.

SMPS Fan [ON] / [OFF]

SMPS Fan Rdy

Check whether the fan is in locked

state.

SMPS Fan Rdy.

[Ready] / [Not Ready]

Duplex Fan

The fan will run or stop.

Duplex Fan [ON] / [OFF]

The procedure and content above may vary, depending on the situation.

Содержание Aficio SP 5100N
















































































































































































Результаты поиска

Содержание Aficio SP 5100N

Отзывы:

Похожие инструкции для Aficio SP 5100N

Бренды по названию

Популярные бренды

Ricoh Aficio SP 5100N, Руководство по обслуживанию

Результаты поиска

Содержание Aficio SP 5100N

Отзывы:

Похожие инструкции для Aficio SP 5100N

Бренды по названию

Популярные бренды